Step | Action | Value(s) | Yes | No |
|---|---|---|---|---|
Schematic Reference: Outside Rearview Mirror Schematics | ||||
1 | Did you perform the Door Systems Diagnostic System Check? | -- | Go to Step 2 | |
2 |
Does the inside rearview mirror darken? | -- | Go to Step 3 | Go to Automatic Day-Night Mirrors Inoperative in Stationary Windows |
3 | While shining a bright light into the sensor on the mirror face, facing the rear window, observe the driver outside rearview mirror. Does the driver outside rearview mirror darken? | -- | Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems | Go to Step 4 |
4 |
Is the voltage within the specified range? | 0.75-1.5 V | Go to Step 7 | Go to Step 5 |
5 | Is the voltage greater than the specified value? | 1.5 V | Go to Step 13 | Go to Step 6 |
6 | Measure the voltage between the signal circuit of the driver outside rearview mirror and a good ground. Is the voltage within the specified range? | 0.75-1.5 V | Go to Step 9 | Go to Step 8 |
7 |
Is the voltage within the specified range? | 0.75-1.5 V | Go to Step 10 | Go to Step 11 |
8 | Test the signal circuit of the driver outside rearview mirror for an open or short to ground. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find or correct the condition? | -- | Go to Step 17 | Go to Step 12 |
9 | Test the low reference circuit of the driver outside rearview mirror for an open or high resistance. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find or correct the condition? | -- | Go to Step 17 | Go to Step 12 |
10 | Inspect for poor connections at the harness connector of the driver outside rearview mirror face. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find or correct the condition? | -- | Go to Step 17 | Go to Step 14 |
11 | Inspect for poor connections at the harness connector of the driver outside rearview mirror. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find or correct the condition? | -- | Go to Step 17 | Go to Step 15 |
12 | Inspect for poor connections at the harness connector of the inside rearview mirror. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find or correct the condition? | -- | Go to Step 17 | Go to Step 16 |
13 |
Important:: A short to battery positive voltage on the signal circuit of the driver outside rearview mirror will cause permanent damage to both the driver outside rearview mirror face and the inside rearview mirror. Repair the short to voltage in the signal circuit of the driver outside rearview mirror. Refer to Wiring Repairs in Wiring Systems. Did you complete the repair? | -- | Go to Step 17 | -- |
14 | Replace the driver outside rearview mirror face. Refer to Mirror Face Replacement - Outside Electrochromatic . Did you complete the replacement? | -- | Go to Step 17 | -- |
15 | Replace the driver outside rearview mirror. Refer to Outside Rearview Mirror Motor Replacement . Did you complete the replacement? | -- | Go to Step 17 | -- |
16 |
Important: Perform the Compass Calibration and Magnetic Variance when replacing the inside rearview mirror with compass. Replace the inside rearview mirror. Refer to Inside Rearview Mirror Replacement in Stationary Windows. Did you complete the replacement? | -- | Go to Step 17 | -- |
17 | Operate the system in order to verify the repair. Did you correct the condition? | -- | System OK | Go to Step 2 |
