Step | Action | Value(s) | Yes | No |
|---|---|---|---|---|
Schematic Reference: Inside Rearview Mirror Schematics Connector End View Reference: Window Systems Connector End Views | ||||
1 | Did you perform the Diagnostic System Check - Vehicle? | -- | Go to Step 2 | |
2 |
Does the inside rearview mirror darken? | -- | Go to Step 3 | |
3 | While shining a bright light into the sensor on the mirror face, facing the rear window, observe the driver outside rearview mirror. Does the driver outside rearview mirror darken? | -- | Go to Testing for Intermittent Conditions and Poor Connections | Go to Step 4 |
4 |
Is the measured voltage within the specified value? | 0.75-1.5 V | Go to Step 7 | Go to Step 5 |
5 | Is the voltage greater than the specified value? | 1.5 V | Go to Step 18 | Go to Step 6 |
6 | Measure the voltage between the automatic day/night mirror signal circuit of the driver outside mirror element and ground. Is the voltage within the specified range? | 0.75-1.5 V | Go to Step 13 | Go to Step 12 |
7 |
Is the measured voltage within the specified range? | 0.75-1.5 V | Go to Step 14 | Go to Step 8 |
8 | Is the voltage greater than the specified value? | 1.5 V | Go to Step 18 | Go to Step 9 |
9 |
Does the resistance measure less than the specified value? | 3 Ω | Go to Step 10 | Go to Step 15 |
10 | Measure the resistance between the automatic day/night mirror signal circuit of the driver outside mirror element and good ground. Is the measured voltage within the specified value? | OL | Go to Step 11 | Go to Step 15 |
11 | Measure the resistance of the automatic day/night mirror low reference circuit of the driver outside rearview mirror element between the driver outside rearview mirror element and the DDM. Is the resistance less than the specified value? | 3 Ω | Go to Step 17 | Go to Step 15 |
12 | Test the automatic day/night mirror signal circuit of the driver outside rearview mirror element for an open, high resistance, or short to ground. Refer to Circuit Testing and Wiring Repairs . Did you find or correct the condition? | -- | Go to Step 23 | Go to Step 16 |
13 | Test the automatic day/night mirror low reference circuit of the driver outside rearview mirror element for an open, high resistance, or short to ground. Refer to Circuit Testing and Wiring Repairs . Did you find or correct the condition? | -- | Go to Step 23 | Go to Step 16 |
14 | Check for poor connections at the harness connector of the driver outside rearview mirror face. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs . Did you find or correct the condition? | -- | Go to Step 23 | Go to Step 19 |
15 | Check for poor connections at the harness connector of the driver outside mirror face. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs . Did you find or correct the condition? | -- | Go to Step 23 | Go to Step 20 |
16 | Check for poor connections at the harness connector of the Inside rearview mirror. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs . Did you find or correct the condition? | -- | Go to Step 23 | Go to Step 21 |
17 | Check for poor connections at the harness connector of the DDM. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs . Did you find or correct the condition? | -- | Go to Step 23 | Go to Step 22 |
18 |
Important:: A short to voltage in the signal circuit of the driver outside rearview mirror element will cause permanent damage to both the driver outside rearview mirror element and the inside rearview mirror. Locate and repair a short to voltage in the automatic day/night mirror signal circuit of the driver outside rearview mirror element. Refer to Wiring Repairs . Did you complete the repair? | -- | Go to Step 23 | -- |
19 | Replace the driver outside rearview mirror. Refer to Outside Rearview Mirror Glass Replacement . Did you complete the replacement? | -- | Go to Step 23 | -- |
20 | Replace the driver outside rearview mirror. Refer to Outside Rearview Mirror Glass Replacement . Did you complete the replacement? | -- | Go to Step 23 | -- |
21 | Replace the inside rearview mirror. Refer to Inside Rearview Mirror Replacement . Did you complete the replacement? | -- | Go to Step 23 | -- |
22 | Replace the driver door module. Refer to Control Module References for replacement, setup, and programming. Did you complete the replacement? | -- | Go to Step 23 | -- |
23 | Operate the system to verify the repair. Did you correct the condition? | -- | System OK | Go to Step 2 |
