Diagnostic Instructions

DTC Descriptor

DTC P1833: Torque Converter Clutch (TCC)/Shift Solenoid (SS) Control Circuit Low Voltage

DTC P1834: Torque Converter Clutch (TCC)/Shift Solenoid (SS) Control Circuit High Voltage

Diagnostic Fault Information

Circuit	Short to Ground	Open/High Resistance	Short to Voltage
High Side Driver 2	P1833	P1833	P1834

Circuit/System Description

The transmission control module (TCM) provides voltage to the pressure control solenoid, the shift solenoids, and the torque converter clutch pulse width modulated (TCC PWM) solenoid through two separate solid-state devices called high side drivers, called HSD1 and HSD2. HSD1 provides electrical power to the pressure control solenoid. HSD2 provides power to the shift solenoids. A normal function of the TCM is to run tests on each driver to ensure that it is functioning properly.

Conditions for Running the DTC

P1833

The engine run time is greater than 5 seconds.

P1834

The ignition is ON.

Conditions for Setting the DTC

P1833

The TCM detects a short to ground on the HSD2 circuit when the HSD2 is commanded ON.

P1834

The TCM detects greater than 6.4 volts at the HSD2 terminal prior to commanding the HSD2 ON.

Action Taken When the DTC Sets

Conditions for Clearing the DTC

DTC P1833 and P1834 are Type B DTCs.

Diagnostic Aids

1. P1833 and P1834 only sets on the High Side Driver 2 side of the shift solenoids. Electrical faults on the ground side of the shift solenoids will set the shift solenoids code for that circuit.
2. An open on the High Side Driver 2 side of the shift solenoids will set one or more of the shift solenoid codes.
3. When a code is set, the TCM turns OFF power to HSD2.

Reference Information

Schematic Reference

Automatic Transmission Controls Schematics

Connector End View Reference

Component Connector End Views

Description and Operation

Transmission General Description

Electrical Information Reference

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions

Scan Tool Reference

Transmission Control Module Scan Tool Information

Special Tools

Circuit/System Verification

Ignition ON, engine OFF. With a scan tool, observe the High Side Driver 2 parameter status for:

Circuit/System Testing

1. Ignition OFF, disconnect the X175 harness connector.
2. Install the J 45681 harness on the transmission pass-thru connector.
3. Using the brown J35616-6 test probes from the most current J 35616 kit , test the resistance for the following: 1-2 Shift Solenoid Valve, 2-3 Shift Solenoid Valve, 4-5 Shift Solenoid Valve, TCC PWM Solenoid Valve. Refer to Component Resistance.

⇒	If less than the specified value, test the affected circuits for a short together condition. If circuits test normal, replace the affected solenoid.

⇒	If greater than the specified value, test the affected circuits for an open. If circuits test normal, replace the affected solenoid.

4. Test for greater than 10 K ohms between the solenoid supply voltage circuit, terminal 17, and all other circuits of the J 45681 harness , except:

•	1-2 Shift Solenoid Valve Control circuit, pin 14

•	2-3 Shift Solenoid Valve Control circuit, pin 9

•	4-5 Shift Solenoid Valve Control circuit, pin 5

•	TCC PWM Solenoid Valve Control circuit, pin 20

⇒	If less than the specified value, the affected circuits are shorted together. Replace the transmission internal wire harness.

5. Test for greater than 50 K ohms between the solenoid supply voltage circuit, terminal 17, and the transmission case.

⇒	If less than the specified value, test the following circuits and solenoids for short to the transmission case.

•	1-2 Shift Solenoid Valve Control circuit, pin 14

•	2-3 Shift Solenoid Valve Control circuit, pin 9

•	4-5 Shift Solenoid Valve Control circuit, pin 5

•	TCC PWM Solenoid Valve Control circuit, pin 20

6. Remove the J 45681 harness from the transmission pass-thru connector and install it on the engine side of the X175.
7. Key ON, engine OFF. Using the brown J35616-7 test probes from the most current J 35616 kit , test for greater than 50 K ohms between the solenoid supply voltage circuit, terminal 17, and the transmission case.

⇒	If less than the specified value, test the solenoid supply voltage circuit for a short to the transmission case. If circuits test normal, replace the TCM.

8. Disconnect the X1 harness connector at the TCM.

Important: When test probing the TCM harness terminals; it is imperative to use the proper test probe from the most current version of the J 35616 kit . Use the light blue J35616-64B probes.

9. Using a 5A fused jumper wire and the light blue probes J35616-64B, test for greater than 10 K ohms between the solenoid supply voltage circuit, terminal F8, and all other circuits of the X1.

⇒	If less than the specified value, the affected circuits are shorted together.

10. If all circuits and connections test normal, replace the TCM.

Component Testing

1. Ignition OFF, disconnect the X175 harness connector. Install the J 45681 harness on the transmission pass-thru connector.
2. Using the brown J35616-4 test probes form the most current J 35616 kit , test the following: 1-2 Shift Solenoid Valve, 2-3 Shift Solenoid Valve, 4-5 Shift Solenoid Valve, TCC PWM Solenoid Valve. Refer to Component Resistance.

⇒	If less than the specified value, test the affected circuits for a short together. If the circuits test normal, replace the affected solenoid.

⇒	If greater than the specified value, test the affected circuits for an open. If circuits test normal, replace the affected solenoid.

Repair Instructions

Perform the Diagnostic Repair Verification after completing the diagnostic procedure.