GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Cadillac 🢒 2007 🢒 STS 🢒 Engine 🢒 Engine Mechanical - 3.6L 🢒 Battery Negative Cable Replacement

Battery Negative Cable Replacement LY7

Removal Procedure

Important: 

   • Always use replacement cables that are of the same type, diameter and length of the cables that you are replacing.
   • Always route the replacement cable the same as the original cable.


    Object Number: 1484712 Size: SH
  1. Disconnect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection .
  2. Disconnect the instrument panel (I/P) harness electrical connector (1) from the battery current sensor.

    3. Object Number: 772418 Size: SH
  3. Remove the bolt (1) securing the negative battery cable to the side rail.
  4. Disconnect the body harness connector (3) from the negative battery cable.

    5. Object Number: 1522523 Size: SH
  5. Remove the stud securing the negative battery cable to the engine block.
  6. Lower the vehicle.
  7. Remove the negative battery cable.

Installation Procedure

    Object Number: 1522523 Size: SH
  1. Install and position the negative battery cable.

    2. Notice: Refer to Fastener Notice in the Preface section.

  2. Install the negative battery cable to engine block stud.

    3. Tighten
    Tighten the stud to 50 N·m (37 lb ft).


    Object Number: 772418 Size: SH
  3. Install the bolt (1) securing the negative battery cable to the side rail.

    4. Tighten
    Tighten the bolt to 36 N·m (27 lb ft).

  4. Connect the body harness connector (3) to the negative battery cable.

    5. Object Number: 1484712 Size: SH
  5. Connect the I/P harness electrical connector (1) to the battery current sensor.
  6. Connect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection .

Battery Negative Cable Replacement LH2

Removal Procedure

Important: 

   • Always use replacement cables that are of the same type, diameter and length of the cables that you are replacing.
   • Always route the replacement cable the same way as the original cable.


    Object Number: 1484712 Size: SH
  1. Disconnect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection .
  2. Remove the fuel injector sight shield. Refer to Fuel Injector Sight Shield Replacement .
  3. Disconnect the instrument panel (I/P) harness electrical connector (1) from the battery current sensor.

    4. Object Number: 1201077 Size: SH
  4. Disconnect the cable retaining clip from the stud on the shock tower.
  5. Remove the bolt securing the negative battery cable to the shock tower.

    6. Object Number: 1201078 Size: SH
  6. Disconnect the instrument panel harness connector from the negative battery cable.
  7. Disconnect the cable retaining clips from the engine bracket.

    8. Object Number: 1201076 Size: SH
  8. Remove the bolt securing the negative battery cable to the engine block.
  9. Remove the negative battery cable.

Installation Procedure
  1. Position the negative battery cable to the engine.

    2. Notice: Refer to Fastener Notice in the Preface section.


    Object Number: 1201076 Size: SH
  2. Install the bolt securing the negative battery cable to the engine block.

    3. Tighten
    Tighten the bolt to 25 N·m (18 lb ft).


    Object Number: 1201078 Size: SH
  3. Connect the cable retaining clips to the engine bracket.
  4. Connect the instrument panel harness connector to the negative battery cable.

    5. Object Number: 1201077 Size: SH
  5. Install the bolt securing the negative battery cable to the shock tower.

    6. Tighten
    Tighten the bolt to 10 N·m (89 lb in).

  6. Connect the cable retaining clip to the stud on the shock tower.

    7. Object Number: 1484712 Size: SH
  7. Connect the I/P harness electrical connector (1) to the battery current sensor.
  8. Install the fuel injector sight shield. Refer to Fuel Injector Sight Shield Replacement .
  9. Connect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection .

Battery Negative Cable Replacement LC3

Removal Procedure

Important: 

   • Always use replacement cables that are of the same type, diameter and length of the cables that you are replacing.
   • Always route the replacement cable the same way as the original cable.


    Object Number: 1484712 Size: SH
  1. Disconnect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection .
  2. Remove the left side engine compartment sight shield.
  3. Remove the engine sight shield. Refer to Intake Manifold Sight Shield Replacement .
  4. Disconnect the instrument panel (I/P) harness electrical connector (1) from the battery current sensor.

    5. Object Number: 1201077 Size: SH
  5. Disconnect the cable retaining clip from the stud on the shock tower.
  6. Remove the bolt securing the negative battery cable (2) to the shock tower.

    7. Object Number: 1201078 Size: SH
  7. Disconnect the instrument panel harness connector from the negative battery cable.
  8. Disconnect the cable retaining clips from the engine bracket.

    9. Object Number: 1201076 Size: SH
  9. Remove the bolt securing the negative battery cable to the engine block.
  10. Remove the negative battery cable.

Installation Procedure
  1. Position the negative battery cable to the engine.

    2. Notice: Refer to Fastener Notice in the Preface section.


    Object Number: 1201076 Size: SH
  2. Install the bolt securing the negative battery cable to the engine block.

    3. Tighten
    Tighten the bolt to 25 N·m (18 lb ft).


    Object Number: 1201078 Size: SH
  3. Connect the cable retaining clips to the engine bracket.
  4. Connect the instrument panel harness connector to the negative battery cable.

    5. Object Number: 1201077 Size: SH
  5. Install the bolt securing the negative battery cable (2) to the shock tower.

    6. Tighten
    Tighten the bolt to 10 N·m (89 lb in).

  6. Connect the cable retaining clip to the stud on the shock tower.

    7. Object Number: 1484712 Size: SH
  7. Connect the I/P harness electrical connector (1) to the battery current sensor.
  8. Install the engine sight shield. Refer to Intake Manifold Sight Shield Replacement .
  9. Install the left side engine compartment sight shield.
  10. Connect the negative battery cable to the battery. Refer to Battery Negative Cable Disconnection and Connection .