Circuit Description
An ignition voltage circuit and a ground circuit are supplied to the fuel pump control module. When the ignition switch is in the ON position, the fuel pump control module turns ON the fuel pump to full power within 24 ms. This facilitates rapid fuel prime for 500 ms. The engine control module (ECM) supplies a pulse width modulated (PWM) signal to the fuel pump control module on the fuel pump relay control circuit. The fuel pump control module varies the voltage to the fuel pump based on the signal from the ECM. If the fuel pump control module receives no fuel pump control signal from the ECM within 500 ms, the fuel pump control module will turn OFF output to the fuel pump.
At idle speed, the fuel pump control module sets the voltage potential to the fuel pump to 9.5 volts. This reduces fuel pump noise and vehicle system power requirements. When higher fuel volume is required, such as engine operation above idle, the fuel pump control module increases the voltage potential to the fuel pump to battery voltage.
The fuel pump control module also supplies the fuel pump speed output circuit and the fuel pump motor low reference circuit, which allows for enhanced fuel pump diagnostics. Therefore, the fuel pump control module is capable of diagnosing itself, the fuel pump relay control circuit, and the fuel pump performance. The diagnostic information is communicated from the fuel pump control module to the ECM through the fuel pump speed control feedback circuit.
If the fuel pump control module detects an incorrect voltage on the fuel pump relay control circuit or on the fuel pump speed control feedback circuit, DTC P0230 sets.
DTC Descriptor
This diagnostic procedure supports the following DTC:
DTC P0230 Fuel Pump Relay Control Circuit
Conditions for Running the DTC
| • | The ignition voltage is between 6-18 volts. |
| • | The ignition ON time is more than 2 seconds. |
| • | DTC P0230 runs continuously once the above conditions have been met. |
Conditions for Setting the DTC
| • | The fuel pump control module detects an open or a high resistance on the fuel pump relay control circuit. |
| OR |
| • | The fuel pump control module detects a high resistance on the fuel pump speed control feedback circuit. |
| • | The above condition is present for more than 2 seconds. |
Action Taken When the DTC Sets
| • | The control module stores the DTC information into memory when the diagnostic runs and fails. |
| • | The malfunction indicator lamp (MIL) will not illuminate. |
| • | The control module records the operating conditions at the time the diagnostic fails. The control module stores this information in the Failure Records. |
| • | The driver information center, if equipped, may display a message. |
Conditions for Clearing the DTC
| • | A current DTC Last Test Failed clears when the diagnostic runs and passes. |
| • | A history DTC clears after 40 consecutive warm-up cycles, if no failures are reported by this or any other non-emission related diagnostic. |
| • | Clear the DTC with a scan tool. |
Step | Action | Yes | No |
|---|---|---|---|
Schematic Reference: Engine Controls Schematics Connector End View Reference: Engine Controls Connector End Views or Engine Control Module Connector End Views | |||
1 | Did you perform the Diagnostic System Check - Vehicle? | Go to Step 2 | Go to Diagnostic System Check - Vehicle in Vehicle DTC Information |
2 | Is DTC P0231, P0628, P0629, or P1254 also set? | Go to Step 3 | |
3 |
Did the DTC fail this ignition? | Go to Step 4 | Go to Intermittent Conditions |
4 |
Does the test lamp turn ON and OFF when commanded with a scan tool? | Go to Step 6 | Go to Step 5 |
5 | Test the fuel pump relay control circuit for an open and for high resistance. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 11 | Go to Step 8 |
6 | Test the fuel pump speed control feedback signal circuit for high resistance. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 11 | Go to Step 7 |
7 | Test for shorted terminals and for poor connections at the fuel pump control module. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 11 | Go to Step 9 |
8 | Test for shorted terminals and for poor connections at the engine control module (ECM). Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 11 | Go to Step 10 |
9 | Replace the fuel pump control module. Refer to Fuel Pump Control Module Replacement . Did you complete the replacement? | Go to Step 11 | -- |
10 | Replace the ECM. Refer to Control Module References in Computer/Integrating Systems for replacement, setup, and programming. Did you complete the replacement? | Go to Step 11 | -- |
11 |
Did the DTC fail this ignition? | Go to Step 2 | Go to Step 12 |
12 | Observe the Capture Info with a scan tool. Are there any DTCs that have not been diagnosed? | Go to Diagnostic Trouble Code (DTC) List - Vehicle in Vehicle DTC Information | System OK |
