GM Service Manual Online
For 1990-2009 cars only

Test Description

  1. This test resets HVAC control module and checks for current air temperature actuator DTC.

  2. Ambient air temperature must be above 3°C (38°F) in order for this A/C Compressor test to be run.

Step

Action

Values

Yes

No

Schematic Reference: HVAC Schematics

Connector End View Reference: HVAC Connector End Views

DEFINITION: The temperature cannot be adjusted, or cooling is insufficient during the A/C operation.

1

Did you perform the Vehicle Diagnostic System Check?

--

Go to Step 2

Go to Diagnostic System Check - Vehicle in Vehicle DTC Information

2

  1. Install a scan tool.
  2. Turn ON the ignition, with the engine OFF.
  3. Recalibrate the HVAC actuators. Refer to Actuator Recalibration .
  4. With a scan tool, observe the current DTC list for the HVAC System Automatic.

Does the scan tool display DTC B0408, B0409, B0419 or B0423?

--

Go to Diagnostic Trouble Code (DTC) List - Vehicle

Go to Step 3

3

Place the blower motor switch in each speed position.

Does the blower motor operate in any speed position?

--

Go to Step 4

Go to Blower Motor Inoperative

4

Does the blower motor operate in each speed position?

--

Go to Step 5

Go to Blower Motor Malfunction

5

  1. Place the blower motor switch in the maximum speed position.
  2. Place the mode controls in the vent position.
  3. Alternately, place the recirculation switch in the outside air and recirculation positions.

Does the recirculation door move from the recirculation position to the ambient air position?

--

Go to Step 6

Go to Air Delivery Improper

6

Place the passenger temperature in the OFF position.

Does the Too Hot in Vehicle concern occur when A/C cooling desired?

--

Go to Step 7

Go to Step 9

7

Important:: Ambient air temperature must be above 3°C (38°F).

  1. Cover the sunload sensor.
  2. Start the engine.
  3. Open all panel outlets in order to allow maximum air flow.
  4. Place the air temperature switch to the coldest position.
  5. Place the mode switch in the vent position.
  6. Place the blower motor switch in the maximum speed position.
  7. Ensure that the vent indicator is not illuminated.

Does the A/C compressor operate?

--

Go to Step 8

Go to HVAC Compressor Clutch Does Not Engage

8

Perform the A/C system performance test. Refer to Air Conditioning (A/C) System Performance Test in Heating, Ventilation and Air Conditioning.

Did you find and correct the condition?

--

Go to Step 24

Go to Step 9

9

Inspect the upper left, upper right, lower left, and lower right air temperature sensors for the following conditions:

    • An obstruction to the airflow
    • A damaged or a missing seal to the sensor
    • Misaligned air ducts
    • A misaligned temperature sensor

Did you find and correct the condition?

--

Go to Step 24

Go to Step 10

10

  1. Turn ON the ignition, with the engine OFF.
  2. Inspect for airflow through the inside air temperature assembly by placing a 5 cm (2 in) square piece of paper over the sensor air inlet.

Does the paper stay in place?

--

Go to Step 11

Go to Step 14

11

  1. Install a thermometer near the upper left, upper right, lower left and lower right air sensors and the inside air temperature assembly.
  2. With a scan tool, observe the following data parameters in the HVAC System Automatic data list:
  3. • Left AC Duct Temp.
    • Left Htr. Duct Temp.
    • Right AC Duct Temp.
    • Right Htr. Duct Temp.
    • Inside Air Temp.

Does the scan tool indicate that the sensor temperatures are within the specifications at the thermometer temperatures?

-3 to 3°C

(-5 to 5°F)

Go to Step 12

Go to Step 17

12

  1. Turn the engine OFF.
  2. Cover the sunload sensor.
  3. Start the engine.
  4. Place the driver side temperature at 22°C (72°F).
  5. With a scan tool, observe the Solar Sensor Data parameter in the HVAC System Automatic data list.

Does the scan tool indicate that the Solar Sensor parameter is greater than the specified value?

224 Counts

Go to Step 13

Go to Step 19

13

  1. Uncover the sunload sensor.
  2. Direct a light source at the sunload sensor.

Do the counts change?

--

System OK

Go to Step 19

14

  1. Disconnect inside air temperature assembly.
  2. Turn ON the ignition, with the engine OFF.
  3. Connect a test lamp between the ignition 3 circuit of the inside air temperature assembly and the inside air temperature assembly control circuit of the inside air temperature assembly.

Does the test lamp illuminate?

--

Go to Step 18

Go to Step 15

15

Test the ignition 3 voltage circuit of the inside air temperature assembly for a high resistance or an open. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 24

Go to Step 16

16

Test the inside air temperature assembly control circuit of the inside air temperature assembly for a short to voltage, a high resistance or an open. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 24

Go to Step 20

17

Test the suspect temperature sensor resistance. Refer to Sensor Resistance Table .

Does the resistance measure near the Sensor Resistance Table?

--

Go to Step 20

Go to Step 18

18

Inspect for poor connections at the harness connector of the suspect air temperature sensor. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 24

Go to Step 21

19

Inspect for poor connections at the harness connector of the sunload sensor. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 24

Go to Step 22

20

Inspect for poor connections at the harness connector of the HVAC control module. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 24

Go to Step 23

21

Replace the appropriate temperature sensor. Refer to the following procedures:

Did you complete the replacement?

--

Go to Step 24

--

22

Replace the sunload sensor. Refer to Sun Load Sensor Replacement .

Did you complete the replacement?

--

Go to Step 24

--

23

Important: Perform the recalibration procedure for the HVAC control module.

Replace the HVAC control module. Refer to HVAC Control Module Replacement .

Did you complete the replacement?

--

Go to Step 24

--

24

Operate the system in order to verify the repair.

Did you correct the condition?

--

System OK

Go to Step 3