GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Cadillac 🢒 2005 🢒 XLR 🢒 Body 🢒 Roof 🢒 Folding Top Stowage Compartment Lid Replacement

Removal Procedure

    Object Number: 1294372 Size: SH
  1. Place the folding top in the up position.
  2. Open the rear compartment.
  3. Locate the hydraulic pump beneath the carpet in the storage compartment on the driver side of the rear compartment.

    4. Object Number: 1274131 Size: SH
  4. Turn the pump bypass valve (1) counterclockwise until the valve stops turning.
  5. Place a protective covering over the interior and the adjacent body panels.
  6. Remove the rear compartment lid trim. Refer to Rear Compartment Lid Inner Panel Trim Replacement in Body Rear End.
  7. Remove the antenna ground plate. Refer to Antenna Ground Plate Replacement in Entertainment.
  8. Remove the wire harness from the rear compartment lid.

    9. Object Number: 1251422 Size: SH
  9. Remove the P-clips (1) from the hydraulic and the electrical lines.

    10. Object Number: 1245292 Size: SH
  10. Using a grease pencil, mark the location of the nuts to the rear compartment lid link.
  11. With the aid of an assistant, remove the nuts (3) from the rear compartment lid (1). Remove the lid from the vehicle.

Disassembly Procedure
  1. Remove the overslam bumpers from the rear compartment lid.
  2. Remove the lid striker.
  3. Remove the backup lamp. Refer to Backup Lamp Replacement in Lighting Systems.
  4. Remove the license lamp. Refer to Rear License Lamp Replacement in Lighting Systems.
  5. Remove the high mounted stop lamp. Refer to High Mount Stop Lamp Replacement in Lighting Systems.

Assembly Procedure
  1. Install the high mounted stop lamp. Refer to High Mount Stop Lamp Replacement in Lighting Systems.
  2. Install the license lamp. Refer to Rear License Lamp Replacement in Lighting Systems.
  3. Install the backup lamp. Refer to Backup Lamp Replacement in Lighting Systems.
  4. Install the lid striker.
  5. Install the overslam bumpers to the rear compartment lid.

Installation Procedure

    Object Number: 1245292 Size: SH
  1. With the aid of an assistant, position the rear compartment lid (1) to the vehicle. Hand start the lid nuts (3).
  2. Apply LOCTITE™ Blue, GM P/N 12345382 (Canadian P/N 10953489) or equivalent to the bolts.

    3. Notice: Refer to Fastener Notice in the Preface section.

  3. Align the nuts (3) to the marks on the compartment lid link.

    4. Tighten
    Tighten the nuts to 11 N·m (97 lb in).

  4. Install the wire harness to the rear compartment lid.
  5. Install the antenna ground plate. Refer to Antenna Ground Plate Replacement in Entertainment.

    6. Object Number: 1251422 Size: SH
  6. Install the P-clips (1) to the hydraulic and the electrical lines.
  7. Remove the protective covering.

    8. Object Number: 1274131 Size: SH
  8. Turn the pump bypass valve (1) clockwise until the valve stops.
  9. Install the support and the carpet over the hydraulic pump.
  10. Close the rear compartment.
  11. Verify that the lid is aligned properly. Refer to Folding Top Clearance Gap Specifications .
  12. If required, adjust the rear compartment lid. Refer to Folding Top Stowage Compartment Lid Adjustment .
  13. Inspect the folding top for proper operation. Refer to Power Folding Top Description and Operation .
  14. Install the trim panel to the rear compartment lid. Refer to Rear Compartment Lid Inner Panel Trim Replacement in Body Rear End.