Keyless Entry System Inoperative Active

The active keyless entry system is considered to be the device to control the following: door locking/unlocking, trunk access, and panic function. The keyless entry system will unlock the vehicle doors or open the rear compartment when a corresponding button on the keyless entry transmitter is pressed. This is accomplished by the keyless entry transmitter sending a radio frequency signal to the external RF antenna located in the back glass. This antenna is connected via coax cable to the remote control door lock receiver (RCDLR). The RCDLR interprets the signal and activates the requested function via serial data message. Poor performance of the system may be due to:

For the J 43241 Keyless Entry Tester, inspect the keyless entry transmitter part number to determine that it is the correct model for the vehicle. A wrong model transmitter may pass the test, but it will not activate the vehicle remote system.

Schematic Reference

Remote Function Schematics

Connector End View Reference

Component Connector End Views

Description and Operation

Keyless Entry System Description and Operation

Electrical Information Reference

Scan Tool Reference

Control Module References for scan tool information

Special Tools

J 43241 Keyless Entry Tester

Attempt to program the keyless entry transmitter, refer to Transmitter Programming. The transmitter should program.

1. Verify that the transmitter is the correct transmitter for the vehicle.

⇒	If not the correct transmitter, replace the transmitter.

2. Verify the scan tool FOB Programmed parameter for the appropriate transmitter is Yes.

⇒	If not the specified value, program the transmitter. Refer to Transmitter Programming.

3. Place the transmitter on the test pad of the J 43241 and press each transmitter button one at a time. The tester should sound a tone and illuminate a green light with each button press.

⇒	If one or more buttons does not sound the tone and illuminate the green light, replace the transmitter battery and retest with the J 43241 . If the condition continues after battery replacement, replace the transmitter.

4. Inspect the external RF antenna connection at the RCDLR. First, gently pull on the coax connector at the module. If the coax comes out, then it wasn’t seated properly. Remove and carefully inspect the coax connection for bent blades or a bent center pin. Fix coax connection if necessary and re-seat connector until a "click" is heard. Gently pull on the coax connection to make sure it is seated properly.
5. Operate the transmitter while observing the scan tool Fob Function parameter for the appropriate transmitter. The parameter should correspond with the function selected on the transmitter.

⇒	If the parameter does not match the function selected on the transmitter, replace the transmitter.

6. Attempt to program the transmitter, refer to Transmitter Programming. The transmitter should program.

⇒	If the transmitter does not program, test the keyless entry antenna for an open/high resistance. If the circuit tests normal, replace the RCDLR.

Perform the Diagnostic Repair Verification after completing the diagnostic procedure.

Keyless Entry System Inoperative Passive

The passive keyless entry antennas are used as short range low frequency (LF) transmitters. As a vehicle with locked doors is approached with a key fob and the exterior door handle switch is pressed, the keyless entry antenna transmitter broadcasts a challenge to the key fob in an approximately 1 meter range. If the response from the key fob via radio frequency (RF) is valid, the locked door will be passively unlocked/unlatched and allow the door to be opened. A low transmitter battery or radio frequency (RF) interference from aftermarket devices such as 2-way radios, power inverters, cellular phone chargers, computers, etc. may cause a system malfunction. High RF traffic areas, such as gas stations which use pay-at-the-pump RF transponders, may also cause interference that could lead to a malfunction.

Schematic Reference

Remote Function Schematics

Connector End View Reference

Component Connector End Views

Description and Operation

Keyless Entry System Description and Operation

Electrical Information Reference

Scan Tool Reference

Control Module References for Scan Tool Information

Special Tools

J 43241 Keyless Enter Tester

1. Ignition On, observe the scan tool Ext. LF Door Handle Switch, RF Door Handle Switch, and Rear Compartment Lid Release Sw. parameters while pressing their respective touch pads. The parameter should change between Active and Inactive as commanded.

⇒	If the parameter does not cycle between the specified values, refer to Power Door Latch System Malfunction .

2. With the vehicle locked, attempt to passively unlock and access the vehicle at the left door, right door, and rear compartment by approaching the vehicle with a valid transmitter and pressing the touch pad. Each door and rear compartment should unlock and open.

⇒	If both doors and the rear compartment do no unlock and open, refer to Passive Transmitter Malfunction.

⇒	If only one door or the rear compartment do no unlock and open, refer to Antenna Circuit Malfunction.

Passive Transmitter Malfunction

1. Place the keyless entry transmitter on the J 43241 and approach the vehicle. Depress the touch pad. Verify the J 43241 sounds a tone.

⇒	If the tone does not sound, replace the transmitter battery and retest with the J 43241 . If the condition continues after battery replacement, replace the keyless entry transmitter.

2. If all circuits test normal, test or replace the RCDLR.

Antenna Circuit Malfunction

1. Ignition OFF, disconnect the harness connector at the inoperative keyless entry antenna.
2. Ignition ON, verify a test lamp does not illuminate between the signal circuit terminal A and ground.

⇒	If the test lamp illuminates, test the signal circuit for a short to voltage. If the circuit tests normal, replace the RCDLR.

3. Install a DMM between the signal circuit terminal A and the low reference circuit terminal B. Set the DMM to capture AC voltage using the MIN MAX function.
4. Depress the touch pad. Verify the DMM captured and AC voltage signal.

⇒	If an AC voltage was not captured, test the signal circuit and the low reference circuit for a short to ground or an open/high resistance. If the circuits test normal, replace the RCDLR.

5. If all circuits test normal, test or replace the keyless entry antenna.

Perform the Diagnostic Repair Verification after completing the diagnostic procedure.