GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Chevrolet 🢒 2000 🢒 Astro - 2WD 🢒 Body and Accessories 🢒 Interior Trim 🢒 Rear Floor Mat/Carpet Replacement

Rear Floor Mat/Carpet Replacement B 31

Removal Procedure
  1. Unsnap the seat belts from the second seat belt latches.
  2. Remove the seats and the risers from the vehicle. Refer to Rear Bench Seat Replacement in Seats.
  3. Remove the engine cover. Refer to Engine Cover Replacement .
  4. Remove the trim plates from the following: Refer to Carpet Retainer Replacement .
    5. • The front
    • The rear side
    • The rear
  5. Remove the cowl side panel trim. Refer to Cowl Side Trim Panel Replacement .
  6. Remove the right front side door lock pillar garnish molding.
  7. Remove the body side front lower trim panel. Refer to Body Side Front Lower Trim Panel Replacement .
  8. Remove the left body side trim panel. Refer to Body Side Trim Panel Replacement - Left Side .
  9. Remove the right body side trim panel. Refer to Body Side Trim Panel Replacement - Right Side .
  10. Remove the bolt that retains each cargo net anchor to the floor of the vehicle (if equipped).

    11. Object Number: 381835 Size: SH
  11. The carpet bezels are retained by sonic weld and are not to be removed from the carpet.

    12. Object Number: 314670 Size: SH
  12. Remove the carpet from the vehicle.

Installation Procedure

    Object Number: 314670 Size: SH
  1. Install the carpet into the vehicle.

    2. Object Number: 381835 Size: SH
  2. The carpet bezels are retained by sonic weld and are not to be removed.

    3. Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

  3. Install the bolt that retains each cargo net anchor to the floor of the vehicle (if equipped).

    4. Tighten
    Tighten the bolt that retains each cargo net anchor to the floor 2 N·m (18 lb in).

  4. Install the right body side trim panel. Refer to Body Side Trim Panel Replacement - Right Side .
  5. Install the left body side trim panel. Refer to Body Side Trim Panel Replacement - Left Side .
  6. Install the body side front lower trim panel. Refer to Body Side Front Lower Trim Panel Replacement .
  7. Install the cowl side panel trim. Refer to Cowl Side Trim Panel Replacement .
  8. Install the right front side door lock pillar garnish molding.
  9. Install the trim plates at the following doors. Refer to Carpet Retainer Replacement :
    10. • The front
    • The rear side
    • The rear
  10. Install the engine cover. Refer to Engine Cover Replacement .
  11. Install the seats and the risers. Refer to Rear Bench Seat Replacement in Seats.
  12. Snap the seat belts to the second seat belt latches.

Rear Floor Mat/Carpet Replacement B 38

Removal Procedure
  1. Remove the seats and the risers. Refer to Bucket Seat Replacement in Seats
  2. Remove the engine cover. Refer to Engine Cover Replacement
  3. Remove the trim plates from the following doors. Refer to Carpet Retainer Replacement
    4. • The front
    • The rear side
    • The rear
  4. Remove the cowl side panel trim. Refer to Cowl Side Trim Panel Replacement
  5. Remove the right front side door lock pillar garnish molding.
  6. Remove the body side front lower trim panel. Refer to Body Side Front Lower Trim Panel Replacement
  7. Remove the left body side trim panel. Refer to Body Side Trim Panel Replacement - Left Side
  8. Remove the right body side trim panel. Refer to Body Side Trim Panel Replacement - Right Side
  9. Remove the bolt that retains each cargo net anchor to the floor of the vehicle (if equipped).

    10. Object Number: 381835 Size: SH
  10. The carpet bezels are retained by sonic weld and are not to be removed.

    11. Object Number: 314670 Size: SH
  11. Remove the carpet from the vehicle.

Installation Procedure

    Object Number: 314670 Size: SH
  1. Install the carpet into the vehicle.

    2. Object Number: 381835 Size: SH
  2. The carpet bezels are retained by sonic weld and are not to be removed.

    3. Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

  3. Install the bolt that retains each cargo net anchor to the floor of the vehicle (if equipped).

    4. Tighten
    Tighten the bolt that retains each cargo net anchor to the floor 2 N·m (18 lb in).

  4. Install the right body side trim panel. Refer to Body Side Trim Panel Replacement - Right Side .
  5. Install the left body side trim panel. Refer to Body Side Trim Panel Replacement - Left Side .
  6. Install the body side front lower trim panel. Refer to Body Side Front Lower Trim Panel Replacement .
  7. Install the cowl side panel trim. Refer to Cowl Side Trim Panel Replacement .
  8. Install the right front side door lock pillar garnish molding.
  9. Install the trim plates from the following doors. Refer to Carpet Retainer Replacement .
    10. • The front
    • The rear side
    • The rear
  10. Install the engine cover. Refer to Engine Cover Replacement .
  11. Install the seats and the risers. Refer to Bucket Seat Replacement in Seats.