Tools Required

Caution: Refer to Cracked Window Caution in the Preface section.

Important: Before cutting out a stationary window, apply a double layer of masking tape around the perimeter of the painted surfaces and the interior trim.

1. Open the liftgate.
2. Remove the liftgate trim. Refer to Liftgate Trim Panel Replacement .
3. Disconnect the electrical connectors from the liftgate window defogger bus bar.
4. Remove the rear window wiper arm. Refer to Rear Window Wiper Arm Replacement .
5. Remove the rear spoiler. Refer to Rear Spoiler Replacement .

Caution: Refer to Glass and Sheet Metal Handling Caution in the Preface section.

Caution: Refer to Defroster Outlet Caution in the Preface section.

6. Cover the following parts to protect from broken glass:

•	Upper dash pad

•	Defroster outlets and A/C outlets

•	Seats and carpeting





Important: Keep the cutting edge of the tool against the window.

7. Remove the window from the urethane adhesive.

•	Leave a base of urethane approximately 2 mm (0.078 in) on the pinch-weld flange.

•	The only suitable lubrication is clear water.

•	Use J 24402-A  ,  J 39032 or equivalent in order to remove the window.

Important: Keep the cutting edge of the knife/tool against the window. Do this from inside the vehicle.

8. If necessary, use a long utility knife or similar tool to remove the bottom corners of the window from the urethane adhesive.



9. With the aid of an assistant, remove the window (1) from the vehicle.

1. Install the liftgate window into the opening. Refer to Adhesive Installation of Liftgate Windows .
2. Install the rear spoiler. Refer to Rear Spoiler Replacement .
3. Install the rear window wiper arm. Refer to Rear Window Wiper Arm Replacement .
4. Connect the liftgate window defogger electrical connectors to the bus bar.
5. Install the liftgate trim. Refer to Liftgate Trim Panel Replacement .
6. Remove the double layer of masking tape around the perimeter of the painted surfaces and the interior trim.
7. Close the liftgate.

Special Tools

Warning: Refer to Cracked Window Warning in the Preface section.

Note: Before cutting out a stationary window, apply a double layer of masking tape around the perimeter of the painted surfaces and the interior trim.

1. Open the liftgate.
2. Remove the liftgate trim. Refer to Liftgate Trim Panel Replacement.
3. Disconnect the electrical connectors from the liftgate window defogger bus bar.
4. Remove the rear window wiper arm. Refer to Rear Window Wiper Arm Replacement.
5. Remove the rear spoiler. Refer to Rear Spoiler Replacement.

Warning: Refer to Defroster Outlet Warning in the Preface section.

6. Cover the following parts to protect from broken glass:

•	Upper dash pad

•	Defroster outlets and A/C outlets

•	Seats and carpeting

Warning: Refer to Glass and Sheet Metal Handling Warning in the Preface section.




7. Using a utility knife, carefully cut the lace (1) from the sides and the top edge of the window to access the urethane adhesive bead, if equipped.




Note: Keep the cutting edge of the tool against the window.

8. Remove the window from the urethane adhesive.

•	Leave a base of urethane approximately 2 mm (0.078 in) on the pinch-weld flange.

•	The only suitable lubrication is clear water.

•	Use J 24402-A  ,  J 39032 or equivalent in order to remove the window.

Note: Keep the cutting edge of the knife/tool against the window. Do this from inside the vehicle.

9. If necessary, use a long utility knife or similar tool to remove the bottom corners of the window from the urethane adhesive.



10. With the aid of an assistant, remove the window (1) from the vehicle.

1. Install the liftgate window into the opening. Refer to Adhesive Installation of Liftgate Windows.
2. Install the rear spoiler. Refer to Rear Spoiler Replacement.
3. Install the rear window wiper arm. Refer to Rear Window Wiper Arm Replacement.
4. Connect the liftgate window defogger electrical connectors to the bus bar.
5. Install the liftgate trim. Refer to Liftgate Trim Panel Replacement.
6. Remove the double layer of masking tape around the perimeter of the painted surfaces and the interior trim.
7. Close the liftgate.