GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Chevrolet 🢒 2009 🢒 Captiva Sport 🢒 Brakes 🢒 Hydraulic Brakes 🢒 Brake Pedal Assembly Replacement

Removal Procedure
  1. Remove the driver knee bolster reinforcement. Refer to Driver Knee Bolster Reinforcement Replacement.
  2. Remove the accelerator pedal position sensor. Refer to Accelerator Pedal Position Sensor Replacement for the 2.4L engine, or Accelerator Pedal Position Sensor Replacementfor the 3.5L engine, or Accelerator Pedal Position Sensor Replacement for the 3.6L engine.
  3. Remove the stop lamp switch. Refer to Stop Lamp Switch Replacement.

    4. Object Number: 1874783 Size: SH
  4. Remove the brake booster pushrod retainer (1).
  5. Disconnect the brake booster pushrod from the brake pedal pivot pin.

    6. Object Number: 1874784 Size: SH
  6. Remove the brake pedal bracket bolt (1).
  7. Remove the instrument panel tie bar. Refer to Instrument Panel Tie Bar Replacement.

    8. Object Number: 1874785 Size: SH
  8. Remove the 2 nuts (1) and the brake pedal assembly.

Installation Procedure

    Object Number: 1874785 Size: SH
  1. Install the brake pedal assembly to the dash panel reinforcement plate.

    2. Notice: Refer to Fastener Notice in the Preface section.

  2. Install the 2 nuts (1).

    3. Tighten
    Tighten the nuts to 25 N·m (18 lb ft).


    Object Number: 1874784 Size: SH
  3. Install the instrument panel tie bar. Refer to Instrument Panel Tie Bar Replacement.
  4. Install the brake pedal bracket bolt (1).

    5. Tighten
    Tighten the bolt to 25 N·m (18 lb ft).

  5. Connect the brake booster pushrod to the brake pedal pivot pin.

    6. Object Number: 1874783 Size: SH
  6. Install the brake booster pushrod retainer (1).

    7. Ensure the pushrod retainer is properly installed by rotating the retainer 360 degrees.

  7. Install the accelerator pedal position sensor. Refer to Accelerator Pedal Position Sensor Replacement for the 2.4L engine, or Accelerator Pedal Position Sensor Replacement for the 3.5L engine, or Accelerator Pedal Position Sensor Replacement for the 3.6L engine.
  8. Install the stop lamp switch. Refer to Stop Lamp Switch Replacement.
  9. Install the driver knee bolster reinforcement. Refer to Driver Knee Bolster Reinforcement Replacement.

Removal Procedure
  1. Remove the driver knee bolster reinforcement. Refer to Driver Knee Bolster Reinforcement Replacement .
  2. Remove the accelerator pedal position sensor. Refer to Accelerator Pedal with Position Sensor Assembly Replacement for the 2.4L engine, or Accelerator Pedal Position Sensor Replacement for the 3.5L engine, or Accelerator Pedal Position Sensor Replacement for the 3.6L engine.
  3. Remove the stop lamp switch. Refer to Stop Lamp Switch Replacement .

    4. Object Number: 1874783 Size: SH
  4. Remove the brake booster pushrod retainer (1).
  5. Disconnect the brake booster pushrod from the brake pedal pivot pin.

    6. Object Number: 1874784 Size: SH
  6. Remove the brake pedal bracket bolt (1).
  7. Remove the instrument panel tie bar. Refer to Instrument Panel Tie Bar Replacement .

    8. Object Number: 1874785 Size: SH
  8. Remove the 2 nuts (1) and the brake pedal assembly.

Installation Procedure

    Object Number: 1874785 Size: SH
  1. Install the brake pedal assembly to the dash panel reinforcement plate.

    2. Caution: Refer to Fastener Caution in the Preface section.

  2. Install the 2 nuts (1) and tighten to  25 N·m (18 lb ft) .

    3. Object Number: 1874784 Size: SH
  3. Install the instrument panel tie bar. Refer to Instrument Panel Tie Bar Replacement .
  4. Install the brake pedal bracket bolt (1) and tighten to  25 N·m (18 lb ft) .
  5. Connect the brake booster pushrod to the brake pedal pivot pin.

    6. Object Number: 1874783 Size: SH
  6. Install the brake booster pushrod retainer (1).

    7. Ensure the pushrod retainer is properly installed by rotating the retainer 360 degrees.

  7. Install the accelerator pedal position sensor. Refer to Accelerator Pedal with Position Sensor Assembly Replacement for the 2.4L engine, or Accelerator Pedal Position Sensor Replacement for the 3.5L engine, or Accelerator Pedal Position Sensor Replacement for the 3.6L engine.
  8. Install the stop lamp switch. Refer to Stop Lamp Switch Replacement .
  9. Install the driver knee bolster reinforcement. Refer to Driver Knee Bolster Reinforcement Replacement .