Fuel Injector Balance Test Procedure
Step
| Action
| Value(s)
| Yes
| No
|
1
| Was
the Powertrain On-Board Diagnostic (OBD) System Check performed?
| --
|
Go to Step 2
| Go
to
Powertrain On Board Diagnostic (OBD) System Check
|
2
| Was the Fuel Injector
Coil Test performed?
| --
|
Go to Step 3
| Go to
Fuel Injector Solenoid Coil Test
|
3
| Is the engine coolant temperature above the specified value?
| 94°C (201°F)
|
Go to Step 4
|
Go to Step 5
|
4
| Allow the engine to
cool below the specified value.
Is the engine coolant temperature below the specified value?
| 94°C (201°F)
|
Go to Step 5
| --
|
5
|
Caution: Relieve the fuel system pressure before servicing fuel system components
in order to reduce the risk of fire and personal injury.
After relieving the system pressure, a small amount of fuel may be released
when servicing the fuel lines or connections. In order to reduce the chance
of personal injury, cover the regulator and the fuel line fittings with a
shop towel before disconnecting. This will catch any fuel that may leak out.
Place the towel in an approved container when the disconnection is complete.
- Install the fuel pressure gauge.
- Energize the fuel pump using the scan tool.
- Place the bleed hose of the fuel pressure gauge into an approved
gasoline container.
- Bleed the air out of fuel pressure gauge.
- Using a scan tool pressurize the fuel system.
- Wait for the fuel pressure to build.
Important: The fuel pump will run for approximately 2 seconds. Repeat Step 4 as
necessary in order to achieve the highest possible fuel pressure.
- Observe the reading on the fuel pressure gauge.
Is the fuel pressure within the specified limits?
| 284-325 kPa (41-47 psi)
|
Go to Step 6
| Go to
Fuel System Diagnosis
|
6
| Turn the fuel pump
OFF.
Does the fuel pressure remain constant?
| --
|
Go to Step 7
| Go to
Fuel System Diagnosis
|
7
|
- Connect the J 39021 fuel injector tester to a fuel injector.
- Set the amperage supply selector switch on the fuel injector tester
to the Balance Test 0.5-2.5 amp
position.
- Turn the fuel pump ON then OFF in order to pressurize the fuel
system.
- Record the fuel pressure indicated by the fuel pressure gauge
after the fuel pressure stabilizes. This is the 1st pressure reading.
- Energize the fuel injector by depressing the Push to Start Test
button on the fuel injector tester.
- Record the fuel pressure indicated by the fuel pressure gauge
after the fuel pressure gauge needle has stopped moving. This is the 2nd pressure
reading.
- Repeat Steps 1 through 6 for each fuel injector.
- Subtract the 2nd pressure reading from the 1st pressure reading
for one fuel injector. The result is the pressure drop value.
- Obtain a pressure drop value for each fuel injector.
- Add all of the individual pressure drop values. This is the total
pressure drop.
- Divide the total pressure drop by the number of fuel injectors.
This is the average pressure drop.
Does any fuel injector have a pressure drop value that is either higher
than the average pressure drop or lower than the average pressure drop by
the specified value?
| 10 kPa (1.5 psi)
|
Go to Step 8
| Go
to Symptoms
|
8
|
Notice: Do not repeat any portion of this test before running the engine in
order to prevent the engine from flooding.
Re-test any fuel injector that does not meet the specification.
Refer to the procedure in Step 7.
Does any fuel injector still have a pressure drop value that is either
higher than the average pressure drop or lower than the average pressure drop
by the specified value?
| 10 kPa (1.5 psi)
|
Go to Step 9
| Go
to Symptoms
|
9
| Replace the faulty fuel injector(s). Refer to
Fuel Injector Replacement
Is the action complete?
| --
| System
OK
| --
|
