Rear Bumper Fascia Replacement Oldsmobile

1. Remove the cargo net and the retainers.
2. Pull back the rear compartment trim at the tail lamps in order to expose the filler panel nut and inside fascia bolts.
3. Remove the filler panel nut from inside the rear compartment.
4. Remove the inside rear bumper fascia bolts from inside the rear compartment.
5. Remove the bolts at the front support bracket (inside the wheel well).
6. Remove the license plate lamp. Refer to Rear License Lamp Replacement in Lighting Systems.
7. Remove the push-in retainers from the upper and lower edge of the rear bumper fascia.
8. Remove the rear bumper fascia from the vehicle.



9. Remove the screws from the rear support bracket (5).
10. Remove the push-in retainer from the support bracket.
11. Remove the rear support bracket from the rear bumper fascia.
12. Lift up to remove the reinforcement bracket from the filler panel.

1. Position the rear support bracket (5) to the rear bumper fascia (3).
2. Install the push-in retainer to the rear support bracket.

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

3. Install the rear support bracket screws.

Tighten
Tighten the rear support bracket screws to 3 N·m (27 lb in).

4. Install the reinforcement bracket to the filler panel.
5. Position the rear bumper fascia to the vehicle.
6. Install the push-in retainers to the top of the rear fascia.
7. Install the rear support bracket bolts.

Tighten
Tighten the rear support bracket bolts to 3 N·m (27 lb in).

8. Install the filler panel nut inside the rear compartment.

Tighten
Tighten the filler panel nut to 3 N·m (27 lb in).

9. Install the inside fascia bolts inside the rear compartment.

Tighten
Tighten the inside rear bumper fascia bolts to 3 N·m (27 lb in).

10. Install the license plate lamp. Refer to Rear License Lamp Replacement in Lighting Systems.
11. Install the push-in retainers at the bottom of the rear bumper fascia.
12. Reposition the rear compartment trim to the original position.
13. Install the cargo net and retainers.

Rear Bumper Fascia Replacement Pontiac

1. Remove the cargo net and the retainers.
2. Pull back the rear compartment trim at the tail lamps in order to expose the filler panel nut and inside fascia bolts.
3. Remove the filler panel nut (1) from inside the rear compartment.
4. Remove the inside rear bumper fascia bolts (2) from inside the rear compartment.
5. Remove the bolts at the front support bracket (3) (inside the wheel well).
6. Remove the license plate lamp. Refer to Rear License Lamp Replacement in Lighting Systems.



7. Remove the push-in retainers from the upper and lower edge of the rear bumper fascia.
8. Remove the rear bumper fascia from the vehicle.
9. Remove the backup lamps. Refer to Backup Lamp Replacement .



10. Remove the screws from the rear support bracket (5).
11. Remove the push-in retainer from the rear support bracket.
12. Remove the rear support bracket from the rear bumper fascia.

1. Install the backup lamps. Refer to Backup Lamp Replacement .



2. Position the rear support bracket (5) to the rear bumper fascia (3).
3. Install the push-in retainer to the rear support bracket.

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

4. Install the rear support bracket screws.

Tighten
Tighten the rear support bracket screws to 2.5 N·m (22 lb in).




5. Position the rear bumper fascia to the vehicle.
6. Install the push-in retainers to the top of the rear fascia.
7. Install the rear support bracket bolts (3).

Tighten
Tighten the rear support bracket bolts to 3 N·m (27 lb in).

8. Connect the electrical connector to the backup lamps.
9. Install the inside rear bumper fascia bolts (2) inside the rear compartment.

Tighten
Tighten the inside rear bumpers fascia bolts to 3 N·m (27 lb in).

10. Install the push-in retainers at the bottom of the rear bumper fascia.
11. Install the license plate lamp. Refer to Rear License Lamp Replacement in Lighting Systems.
12. Reposition the rear compartment trim to the original position.
13. Install the cargo net and retainers.