Important Preliminary Checks Before Starting
Perform the Engine Controls Diagnostic Check before using the symptom
tables. Refer to
Diagnostic System Check - Engine Controls
. Verify that all of the following conditions are true:
| • | The powertrain control module (PCM) and malfunction indicator
lamp (MIL) Service Engine Soon are operating correctly. |
| • | There are no diagnostic trouble codes (DTCs) stored. |
| • | Verify the customer concern. Locate the correct symptom in the
table of contents. Inspect the items indicated under that symptom. |
Visual/Physical Check
Several of the symptom procedures ask for a carefulinspection. This
step is extremely important. This inspection can lead to correcting a
problem without further checks and can save valuable time.
This check includes the following inspections:
| • | The PCM grounds for being clean, tight, and in the proper location |
| • | Vacuum hoses for splits, kinks, and proper connections, as shown
on the Vehicle Emission Control Information label--Check thoroughly
for any type of leak or restriction. |
| • | The mass air flow (MAF) sensor installation--The arrows on
the plastic portion of the sensor must point toward the engine. |
| • | The air intake ducts for being collapsed or for having damaged
areas |
| • | Air leaks at throttle body mounting area, MAF sensor, and the
intake manifold sealing surfaces |
| • | The ignition wires for cracking, hardness, and carbon tracking |
| • | The engine harness wiring and terminals for proper connections,
pinches, or cuts |
Intermittent
Important: Inspect for improper installation of electrical components if an intermittent
condition exists. Inspect for aftermarket theft deterrent devices, lights,
and cellular phones. Ensure that no aftermarket equipment
is connected to the class 2 circuit. If you can not locate
an intermittent condition, a cellular phone signal communication
may cause the condition.
Important: The problem may or may not turn ON the malfunction indicator lamp (MIL)
or store a DTC. DO NOT use the DTC tables for intermittent
problems. The fault must be present in order to locate the problem.
Faulty electrical connections or wiring cause most intermittent problems.
Perform a careful inspectionfor the following conditions:
| • | Poor mating of the connector halves or a terminal not fully seated
in the connector body backed out |
| • | An improperly formed or damaged terminal |
| • | Reform or replace connector terminals in the problem circuit in
order to insure proper contact tension. Refer to
Connector Repairs
in Wiring Systems. |
Road test the vehicle with the DMM connected to the suspected circuit.
An abnormal voltage when the malfunction occurs is a good indication of
a malfunction in the monitored circuit.
Use a scan tool in order to help detect intermittent conditions. The
GM Techline equipment scan tool has several features that you can use
to locate an intermittent condition. Use the following features
to find intermittent faults:
| • | You can trigger the Snapshot feature in order to capture and store
engine parameters within the scan tool when the malfunction occurs. You
can then review this stored information in order to see
what caused the malfunction. |
| • | Using a scan tool Freeze Frame/Failure Records can also aid
in locating an intermittent condition. Review and capture the information
in the Freeze Frame/Failure Record associated with the
intermittent DTC being diagnosed. Drive the vehicle in the
conditions that were present when the DTC originally set. |
| • | You can use the Plot Function on the scan tool in order to plot
selected data parameters. You can then review this stored information. This
may aid in locating an intermittent problem. Refer to the scan
tool Users Guide for more information. |
Important: If the intermittent condition exists as a start and then stall, inspect
for DTCs relating to the vehicle theft deterrent system. Inspect for improper
installation of electrical options such as lights, cellular
phones etc.
Any of the following may cause an intermittent malfunction indicator
lamp (MIL) with no stored DTC:
| • | The ignition coils shorted to a ground, arcing at the ignition
wires or the spark plugs |
| • | The ignition control (IC) wires for being routed to close to the
secondary ignition wires, coils, or the generator--Ensure that all
of the circuits from the PCM to the ignition coils have
good connections. |
| • | An open diode across the A/C compressor clutch and other open
diodes |
Use the following tables when diagnosing a symptom condition:
