The primary fuel level sender and the secondary fuel level sender changes resistance based on fuel level. The PCM monitors the signal circuits of the primary fuel level sender and the secondary fuel level sender in order to determine the fuel level. When the fuel tank is full, the resistance of both fuel level senders are high and the PCM senses a high signal voltage on both the signal circuits of the primary fuel level sender and the secondary fuel level sender. When the fuel tanks are empty, the resistance of the fuel level senders are low and the PCM senses a low signal voltage. The PCM uses the signal circuits of the primary fuel level sender and the secondary fuel level sender in order to calculate the percentage of remaining fuel in the tank. The PCM sends the fuel level percentage via the class 2 serial data circuit to the instrument cluster in order to control the fuel gage. The fuel level information is also used for misfire and EVAP diagnostics.
This diagnostic tests for a lower than normal secondary fuel level sender signal.
The ignition is ON.
• | The secondary fuel level signal is less than 3.5 percent. |
• | The above condition is present for greater than 20 seconds. |
• | The fuel gage defaults to empty. |
• | The low fuel indicator illuminates. |
• | The PCM records the operating conditions at the time the diagnostic fails. The PCM displays the failure information in the Failure Records on the scan tool. |
• | The DTC becomes history when the conditions for setting the DTC are no longer present. |
• | The history DTC clears after 40 malfunction free warm-up cycles. |
• | The PCM receives the clear code command from the scan tool. |
Use the Freeze Frame and/or Failure Records data in order to locate an intermittent condition. If you cannot duplicate the DTC, the information included in the Freeze Frame and/or Failure Records data may aid in determining the number of miles since the DTC set. The Fail Counter and Pass Counter can also aid in determining the number of ignition cycles that the diagnostic reported a pass and/or fail. Operate the vehicle within the same freeze frame conditions (RPM, engine load, vehicle speed, temperature, etc.). This will isolate when the DTC failed.
Refer to Testing for Intermittent Conditions and Poor Connections in Wiring Systems.
The number below refers to the step number on the diagnostic table.
Step | Action | Value(s) | Yes | No | ||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|
Schematic Reference: Instrument Cluster Schematics Connector End View Reference: Master Electrical Component List | ||||||||||||
1 | Did you perform the Instrument Cluster Diagnostic System Check? | -- | Go to Step 2 | |||||||||
2 |
Does the scan tool indicate that the Fuel Tank Level Remaining or the Fuel Level Sensor parameter is less than the specified value? | 4% 0.5 V-6.6L diesel only | Go to Step 3 | Go to Diagnostic Aids | ||||||||
Does the scan tool indicate that the Fuel Tank Level Remaining parameter or the Fuel Level Sensor parameter is greater than the specified value? | 98% 4.5 V-6.6L diesel only | Go to Step 5 | Go to Step 4 | |||||||||
4 | Test the signal circuit of the fuel level sender for a short to ground. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 10 | Go to Step 7 | ||||||||
5 | Test the signal circuit of the fuel level sender for a short to ground between C152 and the fuel level sender. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 10 | Go to Step 6 | ||||||||
6 | Inspect for poor connections at the harness connector of the fuel level sender. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 10 | Go to Step 8 | ||||||||
7 | Inspect for poor connections at the harness connector of the PCM. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 10 | Go to Step 9 | ||||||||
8 | Replace the fuel level sender. Refer to the following procedures:
Did you complete the replacement? | -- | Go to Step 10 | -- | ||||||||
9 |
Important: Program the replacement PCM. Replace the PCM. Refer to:
Did you complete the replacement? | -- | Go to Step 10 | -- | ||||||||
10 |
Does the DTC reset? | -- | Go to Step 2 | System OK |