GM Service Manual Online
For 1990-2009 cars only

Circuit Description

The transfer case shift control module controls the transfer case lock solenoid.

The transfer case lock solenoid is released by being energized. This is accomplished by grounding the lock solenoid control circuit during gears shifts, and in the AUTO or adapt mode. Locking action is applied when power or ground are taken away from the lock solenoid, the transfer case motor is prevented from moving. The system is capable of providing a 2HI, 4HI and 4LO lock-up without the need of additional vehicle power to hold the transfer case in these positions.

This DTC detects an open lock solenoid coil, open motor lock control circuit , or an open motor lock feed circuit.

Conditions for Running the DTC

    • The ignition is ON.
    • System voltage is 9-18 volts.

Conditions for Setting the DTC

    • The transfer case shift control module tries to unapply, turn OFF the lock solenoid by grounding the motor control circuit.
    • If the module does not sense the battery voltage at the motor lock control circuit prior to applying the motor lock, the DTC sets.
    •  Transfer Case Lock output reads back as a high voltage when a low voltage is expected.

Action Taken When the DTC Sets

    • All shifting is disabled.
    • The SERVICE 4WD indicator remains illuminated for the remainder of the current ignition cycle.

Conditions for Clearing the DTC

    • The transfer case shift control module will clear the DTC if the condition for setting the DTC is not currently present.
    • A history DTC will clear after 100 consecutive ignition cycles without a fault present.
    • History DTCs can be cleared using a scan tool.

Test Description

The numbers below refer to the step numbers on the diagnostic table.

  1. Listen for an audible click when the encoder motor brake operates. Command both the ON and OFF states. Repeat the commands as necessary.

  2. This step tests for voltage at the lock solenoid feed side of the encoder motor lock solenoid.

  3. This step verifies that the lock solenoid battery positive circuit is not shorted to power, shorted to ground, or have high resistance.

  4. This step determines if the encoder motor lock solenoid is faulty by checking the internal resistance.

  5. This step tests the control circuit of the encoder motor brake for a short to voltage or an open.

  6. This step determines if a corroded or damaged connector in the encoder motor harness is the cause.

Step

Action

Values

Yes

No

Schematic Reference: Transfer Case Control Schematics

Connector End View Reference: Transfer Case Control Connector End Views

1

Did you perform the Diagnostic System Check - Transfer Case?

--

Go to Step 2

Go to Diagnostic System Check - Transfer Case

2

  1. Install a scan tool.
  2. Turn the ignition ON, with the engine OFF.
  3. Apply the Park brake and put the transmission in Neutral.
  4. With the scan tool, command the transfer case lock control ON and OFF.

Does the encoder motor lock turn ON and OFF with each command?

--

Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems

Go to Step 3

3

  1. Turn the ignition ON with the engine OFF.
  2. Using a DMM, measure the battery positive voltage circuit of the transfer case lock solenoid.

Is the voltage within the specified range?

12.5-14.5

Go to Step 5

Go to Step 4

4

Inspect the lock solenoid battery positive circuit for open, short to ground, or high resistance. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 10

Go to Step 5

5

  1. Disconnect the transfer case encoder motor connector.
  2. Check the internal resistance of the lock solenoid.

Is the resistance within the specified values?

15-25 ohms

Go to Step 6

Go to Step 8

6

  1. Disconnect the transfer case shift control module.
  2. With a DMM, test the lock solenoid control circuit for and short to ground, short to voltage or high resistance.

Did you find and correct the condition?

--

Go to Step 10

Go to Step 7

7

Check all connectors for corrosion or damage. Refer to Connector Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 10

Go to Step 9

8

Replace the encoder motor. Refer to Transfer Case Encoder Motor Replacement .

Did you complete the repair?

--

Go to Step 10

--

9

Replace the transfer case shift control module. Refer to Transfer Case Shift Control Module Replacement and Transfer Case Shift Control Module Reprogramming .

Did you complete the repair?

--

Go to Step 10

--

10

  1. Use the scan tool in order to clear the DTCs.
  2. Operate the vehicle within the Conditions for Running the DTC as specified in the supporting text.

Does the DTC set?

--

Go to Step 2

System OK