GM Service Manual Online
For 1990-2009 cars only

Circuit Description

The steering handwheel position/speed sensor is a 0 to 5 volt device which is used to sense steering wheel position and turning speed. This information is then used by the control module to estimate vehicle lateral acceleration. The two valid output signals are in the 0.35 to 4.75 volt range. These output voltages will increase or decrease within the valid voltage range as the steering wheel is rotated. The sensor is mounted at the base of the steering column.

Conditions for Running the DTC

Vehicle speed is greater than 80.6 km/h (50 mph) for at least 10 seconds.

Conditions for Setting the DTC

The suspension control module detects a steering handwheel position/speed sensor out-of-range condition when the vehicle speed is greater than 80.6 km/h (50 mph) for at least 10 seconds.

Action Taken When the DTC Sets

The electronic variable orifice (EVO) outputs will be disabled.

Conditions for Clearing the MIL/DTC

    • A current DTC will clear when malfunction is no longer present.
    • A history DTC will clear after 100 consecutive ignition cycles with no malfunction present.
    • Using the scan tool

Diagnostic Aids

It is very important that a throrugh inspection of the wiring and connectors be performed. Failure to carefully and fully inspect wiring and connectors may result in misdiagnosis, causing part replacement with reoccurance of the malfunction. An intermittent malfunction can be caused by poor connections, broken insulation, or a wire that is broken or coroded inside the insulation. If an intermittent malfunction exsist refer to Testing for Intermittent Conditions and Poor Connections in wiring systems.

Test Description

The number(s) below refer to the step number(s) on the diagnostic table.

  1. Checking sensor voltage range.

  2. Tests for the proper operation of the circuit in the high voltage range.

  3. Tests for the proper operation of the circuit in the low voltage range. If the fuse in the jumper opens when you perform this test, the sensor 1 signal circuit is shorted to voltage.

  4. Tests for a short to ground in the 5 volt reference circuit.

  5. Test for a short to voltage, a high resistance, or an open circuit.

  6. The control module must be re-calibrated.

Step

Action

Value(s)

Yes

No

Schematic Reference: Steering Assist Schematics

1

Did you perform the RTD Diagnostic System Check?

--

Go to Step 2

Go to Diagnostic System Check - Real Time Damping

2

  1. Install a scan tool.
  2. Turn ON the ignition, with the engine OFF.
  3. With a scan tool, observe the steering handwheel position/speed sensor 1 data parameter in the suspension Control Module data list.
  4. Rotate the steering wheel in both directions while observing the scan tool.

Does the scan tool indicate that the steering handwheel position/speed sensor 1 data parameter changes within the specified range?

0.35-4.7 V

Go to Diagnostic Aids

Go to Step 3

3

  1. Turn OFF the ignition.
  2. Disconnect the steering handwheel position/speed sensor.
  3. Turn ON the ignition, with the engine OFF.
  4. With a scan tool, observe the steering handwheel position/speed sensor 1 data parameter.

Does the scan tool indicate that the steering handwheel position/speed sensor 1 data parameter is greater than the specified value?

4.7 V

Go to Step 4

Go to Step 8

4

  1. Turn OFF the ignition
  2. Connect a 3 amp fused jumper wire between the sensor 1 signal circuit of the steering handwheel position/speed sensor and the low reference circuit of the steering handwheel position/speed sensor.
  3. Turn ON the ignition, with the engine OFF.
  4. With a scan tool, observe the steering wheel position sensor 1 data parameter.

Does the scan tool indicate that the steering handwheel position/speed sensor data parameter is less than the specified value?

0.35 V

Go to Step 5

Go to Step 9

5

Test the 5 volt reference circuit of the steering handwheel position/speed sensor for a short to ground. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 7

Go to Step 6

6

  1. Turn OFF the ignition.
  2. Disconnect the fused jumper wire.
  3. Connect a 3 amp fused jumper wire between the 5 volt reference circuit of the steering handwheel position/speed sensor and the sensor 1 signal circuit of the steering handwheel position/speed sensor.
  4. Turn ON the ignition, with the engine OFF.
  5. With a scan tool, observe the steering handwheel position sensor 1 data parameter.

Does the scan tool indicate that the steering position sensor 1 data parameter is greater than the specified value?

4.7 V

Go to Step 15

Go to Step 12

7

Test the 5 volt reference circuit of the steering handwheel position/speed sensor for a short to voltage, a high resistance, or an open. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 15

Go to Step 11

8

Test the sensor 1 signal circuit of the steering handwheel position/speed sensor for a short to ground. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 15

Go to Step 12

9

Test the sensor 1 signal circuit of the steering handwheel position/speed sensor for a short to voltage, a high resistance, and an open circuit. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 15

Go to Step 10

10

Test the sensor low reference circuit of the steering handwheel position/speed sensor for high resistance and an open circuit. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 15

Go to Step 12

11

Inspect for poor connections at the harness connector of the steering handwheel position/speed sensor. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 15

Go to Step 13

12

Inspect for poor connections at the harness connector of the suspension control module. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 15

Go to Step 14

13

Replace the steering handwheel position/speed sensor. Refer to Steering Wheel Position Sensor or Steering Shaft Lower Bearing Replacement

Did you complete the replacement?

--

Go to Step 15

--

14

Important: Perform the set up procedure for the suspension control module when replacement is necessary.

Replace the suspension control module. Refer to Electronic Suspension Control Module Replacement

Did you complete the replacement?

--

Go to Step 15

--

15

  1. Use the scan tool in order to clear the DTCs.
  2. Operate the vehicle within the conditions for Running the DTC as specified in the supporting text.

Does the DTC reset?

--

Go to Step 2

System OK