Schematic Reference: Door Control Module Schematics

Connector End View Reference: Power Door Systems Connector End Views

Did you perform the Door Systems Diagnostic System Check?

Go to Step 2

Go to Diagnostic System Check - Door Systems

Verify that the passenger door power door lock inoperative fault is present.

Does the passenger door power door lock operate normallly?

Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems

Go to Step 3

Is the driver window, driver door lock and power mirrors inoperative also?

Go to Step 8

Go to Step 4

Is the passenger window inoperative also?

Go to Step 9

Go to Step 5

1. Install a scan tool.
2. Turn ON the ignition, with the engine OFF.
3. Observe the Door Lock Switch and Door Unlock Switch parameters in the Left Door Control Module data list.
4. Actuate the driver door lock switch to LOCK and UNLOCK.

Does the scan tool display Active for the Door Lock Switch and Door Unlock Switch parameters?

Go to Step 6

Go to Step 10

1. Observe the Door Lock Switch and Door Unlock Switch parameters in the Right Door Control Module data list.
2. Actuate the passenger door lock switch to LOCK and UNLOCK.

Does the scan tool display Active for the Door Lock Switch and Door Unlock Switch parameters?

Go to Step 7

Go to Step 11

1. Turn OFF the ignition.
2. Disconnect the passenger door latch C3 connector.
3. Turn ON the ignition, with the engine OFF.
4. Connect a test lamp between the door lock actuator lock control circuit of the passenger door latch C3 connector and the door lock actuator unlock control circuit of the passenger door latch C3 connector.
5. Actuate the driver door lock switch to LOCK and UNLOCK.

Does the test lamp illuminate in both directions?

Go to Step 13

Go to Step 12

Test the driver door switch ground circuit for an open. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 21

Go to Step 14

Test the passenger door switch ground circuit for an open. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 21

Go to Step 15

Test the driver door lock switch signal circuits for a short to voltage or an open. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 21

Go to Step 14

Test the passenger door lock switch signal circuits for a short to voltage or an open. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 21

Go to Step 15

Test the passenger door lock actuator control circuits for an open. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 21

Go to Step 16

Inspect for poor connections at the harness connectors of the passenger door latch. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 21

Go to Step 17

Inspect for poor connections at the harness connector of the driver door switch. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 21

Go to Step 18

Inspect for poor connections at the harness connector of the passenger door switch. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 21

Go to Step 19

Inspect for poor connections at the harness connector of the passenger door module (PDM). Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 21

Go to Step 20

Replace the passenger door latch. Refer to Door Lock Replacement .

Did you complete the replacement?

Go to Step 21

--

Replace the driver door switch. Refer to Front Door Switch Replacement .

Did you complete the replacement?

Go to Step 21

--

Replace the passenger door switch. Refer to Front Door Switch Replacement .

Did you complete the replacement?

Go to Step 21

--

Replace the passenger door module. Refer to Door Control Module Replacement .

Did you complete the replacement?

Go to Step 21

--

Operate the system in order to verify the repair.

Did you correct the condition?

System OK

Go to Step 2