Schematic Reference: Power Roof Systems Component Views

Connector End View Reference: Power Roof Systems Connector End Views

1

Did you perform the Diagnostic System Check - Vehicle?

Go to Step 2

Go to Diagnostic System Check - Vehicle in Vehicle DTC Information

Verify that the Power Folding Top Inoperative complaint is present.

Does the Power Folding Top System operate as described in the System Description and Operation?

Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems

Go to Step 3

Does the folding top cover pull down actuator continuously move up and down?

Go to Folding Top Stowage Compartment Lid Release Inoperative

Go to Step 4

1. Observe the driver information center (DIC) warning messages.
2. Attempt to operate the power folding top.
3. If any DIC messages are displayed as a result of top operation, refer to DIC Warning Messages - Roof .

Did you find and correct the condition?

Go to Step 29

Go to Step 5

From the top closed position, did the folding top start to open then stop?

Go to Power Folding Top Does Not Open

Go to Step 6

From the top open position, did the folding top start to close then stop?

Go to Power Folding Top Does Not Close

Go to Step 7

1. Install a scan tool.
2. Turn ON the ignition, with the engine OFF.
3. With a scan tool, observe the Window Normalization parameter by making the following selections:

•

Roof

•	Data Display

•	Driver Door Module

•	Passenger Door Module

4. View the window normalization parameter for each module.

Did the Window Normalization parameter display NO for either module?

Go to Power Window Reinitialization in Doors

Go to Step 8

1. With a scan tool, observe the inoperative Top Control Switch parameter in the Folding Top Module Inputs data list.
2. Press the inoperative top control switch.

Does the inoperative Top Control Switch parameter change state?

Go to Step 11

Go to Step 9

1. Disconnect the folding top control switch harness connector.
2. Connect a test lamp from the battery positive voltage circuit of the switch connector to a good ground.

Does the test lamp illuminate?

Go to Step 10

Go to Step 24

1. Connect a 3-amp fused jumper wire from the battery positive voltage circuit of the switch connector to the inoperative switch signal circuit of the switch connector.
2. With a scan tool, observe the Top Control Switch parameter in the Folding Top Module Inputs data list.

Did the Top Control Switch parameter change state?

Go to Step 20

Go to Step 17

If the top is in the open position, did the folding top cover release?

Go to Step 12

Go to Folding Top Stowage Compartment Lid Release Inoperative

1. Wait four minutes for the module to release the pressure in the hydraulic system.
2. Manually open the folding top cover to access the hydraulic fluid bypass valve.
3. Turn the hydraulic fluid bypass valve counterclockwise to inhibit folding top movement.
4. With a scan tool navigate to Pump Motor Direction by making the following selections:

•

Roof

•	Special Functions

•	Folding Top Module

5. With the scan tool, command the direction of the motor to the X/A and then Y/B directions.

Can you hear the pump motor respond with each command?

Go to Step 14

Go to Step 13

1. Disconnect the inline harness connector at the pump motor.
2. Connect a test lamp between the pump motor control circuits A and B of the inline connector.
3. With the scan tool, command the direction of the motor to the X/A and Y/B directions.

Does the test lamp illuminate with each command?

Go to Step 22

Go to Step 18

14

With the scan tool command Valve 1 and Valve 2 ON and OFF.

Can an audible click be heard from each valve when commanded ON?

Go to Step 28

Go to Step 15

1. Disconnect the harness connector of the inoperative valve.
2. Connect a test lamp from the control circuit of the valve connector to a good ground.
3. With the scan tool command the Valve ON.

Does the test lamp illuminate when the valve is commanded ON?

Go to Step 16

Go to Step 19

1. Connect a test lamp between the control circuit of the valve connector and the ground circuit of the valve connector.
2. With the scan tool command the Valve ON.

Does the test lamp illuminate when the valve commanded ON?

Go to Step 21

Go to Step 25

Test the appropriate switch signal circuit between the folding top control switch and the folding top control (FTC) module for an open. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 29

Go to Step 23

Test the control circuits of the folding top pump motor for a short to ground or open. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 29

Go to Step 23

Test the control circuit of the inoperative valve for a short to ground or an open. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 29

Go to Step 23

Inspect for poor connections at the harness connector of the FTC switch. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 29

Go to Step 26

Inspect for poor connections at the harness connector of the inoperative valve. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 29

Go to Step 28

Inspect for poor connections at the harness connector of the folding top pump motor. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 29

Go to Step 28

Inspect for poor connections at the harness connector of the FTC module. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 29

Go to Step 27

Repair the short to ground or open in the battery positive voltage circuit of the folding top control switch. Refer to Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 29

--

Repair the high resistance or open in the ground circuit of the inoperative valve. Refer to Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 29

--

Replace the folding top control switch. Refer to Convertible Top Switch Replacement .

Did you complete the replacement?

Go to Step 29

--

Replace the FTC module. Refer to Control Module References in Computer/Integrating Systems for replacement, setup, and programming.

Did you complete the replacement?

Go to Step 29

--

Replace the folding top pump, valve, and motor assembly. Refer to Folding Top Pump with Motor Replacement .

Did you complete the replacement?

Go to Step 29

--

1. Turn OFF the ignition.
2. Disconnect any jumper wires.
3. Connect all previously disconnected components.
4. Replace any open fuses, if necessary.
5. Turn the bypass valve clockwise to allow folding top cover movement.
6. Press the ignition to ACCY or RUN, with the engine OFF.
7. Use the scan tool to clear any DTCs.
8. Operate the system in order to verify the repair.

Did you correct the condition?

System OK

Go to Step 2