Circuit Description
With the ignition ON battery voltage is supplied directly to the reverse inhibit solenoid. The engine control module (ECM) controls the solenoid by grounding the control circuit via an internal switch called a driver. The driver supplies the ground for the component being controlled. Each driver has a fault line which the ECM monitors. When the ECM commands a component ON, the voltage of the control circuit should be low, near 0 volts. When the ECM commands the control circuit to a component OFF, the voltage potential of the circuit should be high, near battery voltage. If the internal fault detection circuit senses a voltage other than what is expected, the fault line status changes, causing DTC P0801 to set. DTC P0801 is a type C DTC.
DTC Descriptor
This diagnostic procedure supports the following DTC:
DTC P0801 Reverse Inhibit Solenoid Control Circuit
Conditions for Running the DTC
| • | The engine is running. |
| • | The vehicle speed is less than 3 km/h (2 mph). |
Conditions for Setting the DTC
| • | The ECM detects that the commanded state of the driver and the actual state of the control circuit do not match. |
| • | Condition must exist for a minimum of 2 seconds. |
Action Taken When the DTC Sets
| • | The ECM stores the DTC information into memory when the diagnostic runs and fails. |
| • | The malfunction indicator lamp (MIL) will not illuminate. |
| • | The ECM records the operating conditions at the time the diagnostic fails and stores this information in the Failure Records. |
Conditions for Clearing the DTC
| • | A scan tool can clear the DTC. |
| • | The ECM clears the DTC from ECM history if the vehicle completes 40 warm-up cycles without a non-emission-related diagnostic fault occurring. |
| • | The ECM cancels the DTC default actions when the fault no longer exists and the DTC passes. |
Diagnostic Aids
| • | Remove any debris from the ECM connector surfaces before servicing the ECM. Inspect the ECM connector gaskets when diagnosing/replacing the ECM. Ensure that the gaskets are installed correctly. The gaskets prevent contaminate intrusion into the ECM. |
| • | For any test that requires probing the ECM or a component harness connector, use the J 35616 connector test adapter kit. Using this kit prevents damage to the harness/component terminals. Refer to Using Connector Test Adapters . |
| • | Low system voltage can cause this DTC to set. When reviewing captured data, verify if a low system voltage condition was present at the time the DTC was stored in memory. |
| • | For an intermittent condition, refer to Testing for Intermittent Conditions and Poor Connections . |
Test Description
The numbers below refer to the step numbers on the diagnostic table.
-
Listen for an audible click when the reverse inhibit solenoid operates. Command both the ON and OFF states. Repeat the commands as necessary.
-
Tests for voltage at the coil side of the reverse inhibit solenoid. The ENG IGN 1 fuse supplies power to the coil side of the reverse inhibit solenoid.
-
Verifies that the ECM is providing ground to the reverse inhibit solenoid.
-
Tests if ground is constantly being applied to the reverse inhibit solenoid.
Step | Action | Yes | No |
|---|---|---|---|
1 | Did you perform the Diagnostic System Check - Vehicle? | Go to Step 2 | |
Important: Record the Freeze Frame and Failure Records before clearing the DTCs. Using the Clear Info function erases the Freeze Frame and Failure Records from the ECM. Does the reverse inhibit solenoid turn ON and OFF? | Go to Step 3 | Go to Step 4 | |
Does the DTC reset? | Go to Step 4 | Go to Testing for Intermittent Conditions and Poor Connections | |
4 |
Does the test lamp illuminate? | Go to Step 5 | Go to Step 11 |
Does the test lamp turn ON and OFF? | Go to Step 9 | Go to Step 6 | |
Does the test lamp remain illuminated with each command? | Go to Step 8 | Go to Step 7 | |
7 | Test the control circuit of the reverse inhibit solenoid for a short to voltage or an open. Refer to Circuit Testing and Wiring Repairs . Did you find and correct the condition? | Go to Step 14 | Go to Step 10 |
8 | Test the control circuit of the reverse inhibit solenoid for a short to ground. Refer to Testing for Short to Ground and Wiring Repairs . Did you find and correct the condition? | Go to Step 14 | Go to Step 10 |
9 | Inspect for poor connections at the reverse inhibit solenoid. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs . Did you find and correct the condition? | Go to Step 14 | Go to Step 12 |
10 | Inspect for poor connections at the harness connector of the ECM. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs . Did you find and correct the condition? | Go to Step 14 | Go to Step 13 |
11 | Test the battery positive voltage circuit of the reverse inhibit solenoid for an open or short to ground. Refer to Wiring Repairs . Did you find and correct the condition? | Go to Step 14 | -- |
12 | Replace the reverse inhibit solenoid. Refer to Reverse Lockout Solenoid Replacement . Did you find and correct the condition? | Go to Step 14 | -- |
13 | Replace the ECM. Refer to Control Module References for replacement, setup, and programming. Did you complete the replacement? | Go to Step 14 | -- |
14 | Perform the following procedure in order to verify the repair:
Has the test run and passed? | Go to Step 15 | Go to Step 2 |
15 | With the scan tool, observe the stored information, capture info and DTC info. Does the scan tool display any DTCs that you have not diagnosed? | System OK |
