GM Service Manual Online
For 1990-2009 cars only

Removal Procedure


    Object Number: 1464324  Size: SH

    Important: The intake manifold, throttle body, fuel injection rail, and injectors may be removed as an assembly. If not servicing the individual components, remove the manifold as a complete assembly.

  1. Remove the engine sight covers (2, 3). Refer to Upper Intake Manifold Sight Shield Replacement .

  2. Object Number: 651871  Size: SH
  3. Disconnect the electrical connector (1) for the fuel injectors.
  4. Disconnect the electrical connectors (3) from the throttle body.
  5. Disconnect the fuel feed for the fuel injectors.

  6. Object Number: 63936  Size: SH
  7. Remove the vacuum hose from the brake booster.
  8. Disconnect the electrical connector from the manifold absolute pressure (MAP) sensor.

  9. Object Number: 1408858  Size: SH
  10. Remove the MAP sensor (714).
  11. Remove the grommet (715) from the sensor, as required.

  12. Object Number: 1408859  Size: SH
  13. Remove the evaporative emission (EVAP) clip (740), bolt (742), bracket (741), valve (730), and tubes (729, 735).

  14. Object Number: 1408860  Size: SH
  15. Remove the intake manifold bolts (512) and fuel rail stop bracket (712).
  16. Remove the intake manifold (500).

  17. Object Number: 1272799  Size: SH
  18. Remove the intake manifold gaskets (514).
  19. Discard the intake manifold gaskets.

Installation Procedure


    Object Number: 1272799  Size: SH

    Important: DO NOT reuse the intake manifold gaskets. Install NEW intake manifold gaskets.

    Important: 

       • The intake manifold, throttle body, fuel injection rail and fuel injectors may be removed as an assembly. If not servicing the individual components, install the intake manifold as a complete assembly.
       • DO NOT use the intake manifold gaskets again. Install NEW intake manifold-to-cylinder head gaskets.

  1. Install NEW intake manifold-to-cylinder head gaskets (514).

  2. Object Number: 1408860  Size: SH
  3. Install the intake manifold (500).
  4. Apply a 5 mm (0.20 in) band of threadlocker to the threads of the intake manifold bolts (512). Refer to Adhesives, Fluids, Lubricants, and Sealers for the correct part number.
  5. Notice: Refer to Fastener Notice in the Preface section.


    Object Number: 63222  Size: SH
  6. Install the fuel rail stop bracket (712).
  7. Install the intake manifold bolts (512).
  8. Tighten

        • First Pass: Tighten the intake manifold bolts in sequence to 5 N·m (44 lb in).
        • Final Pass: Tighten the intake manifold bolts in sequence to 10 N·m (89 lb in).

    Object Number: 1408858  Size: SH
  9. Lubricate the MAP sensor grommet (715) with clean engine oil.
  10. Install the MAP sensor (714) and grommet (715).

  11. Object Number: 1408859  Size: SH
  12. Install the EVAP valve (730), bracket (741), and bolt (742).
  13. Tighten
    Tighten the bolt to 50 N·m (37 lb ft).

  14. Install the EVAP tubes (729, 735).
  15. Install the fuel rail. Refer to Fuel Rail and Injectors Installation .
  16. Reconnect the electrical connector for the MAP sensor.

  17. Object Number: 63936  Size: SH
  18. Install the vacuum hose for the brake booster.

  19. Object Number: 651871  Size: SH
  20. Reconnect the electrical connectors (3) throttle body.
  21. Reconnect the electrical connector (1) for the fuel injectors.
  22. Refill the cooling system. Refer to Cooling System Draining and Filling .

  23. Object Number: 1464324  Size: SH
  24. Install the engine sight covers (2, 3). Refer to Upper Intake Manifold Sight Shield Replacement .