Tools Required

J 21552 Rack Piston Arbor

1. Remove the pitman shaft and side cover. Refer to Steering Gear Pitman Shaft and Housing Cover Replacement - Off Vehicle .
2. Remove the housing end plug (1). Refer to Steering Gear Housing Plug Replacement - Off Vehicle .
3. Turn the stub shaft counterclockwise until the rack piston (2) begins to come out of the steering gear housing.
4. Remove the rack piston plug (1).
5. Insert J 21552 into the bore of the rack piston (2).
6. Hold J 21552 tightly against the worm shaft while turning the stub shaft counterclockwise. Turning the stub shaft forces the race piston (2) onto J 21552 . The rack piston balls remain in place.



7. Remove the following items as an assembly from the steering gear housing (9):

•	The rack piston (4)

•	The rack piston balls (5)

•

J 21552

8. Remove the valve. Refer to Steering Gear Valve Replacement - Off Vehicle .
9. Remove the worm shaft (14).
10. Remove the thrust bearing (12) and the flat races (11) (13).
11. Remove the flat races (11).
12. Remove J 21552 from the rack piston (4).
13. Remove the rack piston balls (5).
14. Remove the following items from the rack piston (4):

14.1.

The screws (8)

14.2.

The clamp (7)

14.3.

The ball guide (6)

15. Remove the teflon ring (2).
16. Remove the O-ring seal (3).
17. Clean all of the disassembled parts.
18. Inspect all of the disassembled parts for wear.
19. Replace the parts if necessary.

Tools Required

1. Install the O-ring seal (3) and the teflon ring (2).
2. Lubricate both parts with power steering fluid.
3. Install the worm shaft (14) to the rack piston (4) outside of the steering gear housing (9).

Important: Reinstall all of the rack piston balls in the rack piston. Improper rack piston ball installation may result in personal injury.

4. Fully seat the worm shaft to the rack piston.



5. Align the worm shaft spiral groove with the rack piston ball return guide hole (1).

Important: The black rack piston balls are smaller than the silver rack piston balls. Install the black and the silver rack piston balls alternately into the rack piston and the ball guide to maintain the rack piston to the worm shaft preload.

6. Lubricate the rack piston balls with power steering fluid.
7. Insert the rack piston balls through the ball return guide hole (1) while turning worm shaft (2) counterclockwise in order to install the rack piston balls into the rack piston.



8. Install the remaining rack piston balls (3) into the ball guide (1) using grease at each end (2) to retain the rack piston balls (3).



9. Install the ball guide (5) to the rack piston (4).
10. Install the ball guide clamp (6).
11. Install the screws (7).

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

Tighten
Tighten the screws (7) to 58 N·m (43 lb in).

12. Insert J 21552 into the bore of the rack piston while turning the worm shaft counterclockwise. The turning of the worm shaft forces the rack piston onto J 21552 . The rack piston balls remain in place.



13. Install the flat races (2) (4) and the thrust bearing (3) onto the worm shaft (1).



14. Install the worm shaft (4) to the steering gear housing (3).
15. Install the valve. Refer to Steering Gear Valve Replacement - Off Vehicle .
16. Install the rack piston (2) to the worm (4) from J 21552 using J 8947 to compress the seals.

Important: Reinstall all of the rack piston balls into the rack piston. Improper rack piston ball installation may result in personal injury.

17. Hold J 21552 tightly against the worm shaft (4).
18. Turn the stub shaft clockwise until the rack piston (2) is seated on the worm shaft (4).
19. Install the rack piston plug.

Tighten
Tighten the rack piston plug to 150 N·m (111 lb ft).

20. Install the housing end plug (1). Refer to Steering Gear Housing Plug Replacement - Off Vehicle .
21. Install the pitman shaft and side cover. Refer to Steering Gear Pitman Shaft and Housing Cover Replacement - Off Vehicle .
22. To adjust the steering gear, refer to:

20.1.

Steering Gear Worm Gear Thrust Bearing Preload Adjustment - Off Vehicle

20.2.

Steering Gear Pitman Shaft Over-Center Preload Adjustment - Off Vehicle