Diagnostic Instructions
| • | Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure. |
| • | Review Strategy Based Diagnosis for an overview of the diagnostic approach. |
| • | Diagnostic Procedure Instructions provides an overview of each diagnostic category. |
Diagnostic Fault Information
Circuit | Short to Ground | Open/High Resistance | Short to Voltage | Signal Performance |
|---|---|---|---|---|
Low Speed GMLAN Serial Data | 1 | 2* | 1 | -- |
Ground (DLC, terminal 5) | -- | 1 | -- | -- |
* An open between the data link connector (DLC) and JX 200, or DLC ground terminal 5 will only effect the communication with the scan tool. The vehicle modules will still communicate. 1. No communication on any low speed GMLAN module 2. No communication on a specific low speed GMLAN module | ||||
Circuit/System Description
Modules connected to the low speed GMLAN serial data circuit monitor for serial data communications during normal vehicle operation. Operating information and commands are exchanged among the modules when the ignition switch is in any position other than OFF. The low speed GMLAN serial data circuit must be operational for the vehicle to start so the vehicle theft deterrent (VTD) module and body control module (BCM) can communicate. The low speed GMLAN serial data circuit uses JX 200 (splice pack comb) as a common connection between some modules and the DLC.
Diagnostic Aids
| • | Use the Data Link References to identify the low speed GMLAN serial data modules. |
| • | This test is used for a total low speed GMLAN communication failure. If only 1 module is not communicating and sets no DTC, ensure that the vehicle is equipped with the module, then use DTC U0100-U0299 for diagnostics. |
| • | An open in the low speed GMLAN serial data circuit between the splice pack (comb) and a module(s) will only effect the specific module(s). This type of failure will set a loss of communication DTC for each module effected, and the other modules will still communicate. |
| • | An open in the DLC ground circuit terminal 5 will allow the scan tool to operate to set up the vehicle on the tool and then not communicate with the vehicle. When the scan tool is to the point of communicating with the vehicle, a message on the scan tool will indicate "no CANdi module detected" and will not communicate. |
| • | An open between the data link connector (DLC) and JX 200 will only effect the communication with the scan tool. The vehicle modules will still communicate, and the vehicle will start. |
| • | The engine will not start when there is a total malfunction of the low speed GMLAN serial data circuit. |
| The following conditions may cause a total loss of low speed GMLAN data communication: |
| - | The low speed GMLAN serial data circuit shorted to ground or voltage. |
| - | A module internal malfunction that causes a short to voltage or ground on the low speed GMLAN circuit. |
| - | An open in the DLC ground circuit. |
Reference Information
Schematic Reference
Connector End View Reference
Description and Operation
Data Link Communications Description and Operation
Electrical Information Reference
Circuit/System Testing
- Test for less than 1.0 ohm between the DLC ground circuit terminal 5 and ground.
- Ignition OFF, disconnect the harness connector (splice pack comb) at JX 200. Install a 3-amp fused jumper wire between JX 200 terminal A and terminal D, harness side.
- Ignition ON, with a scan tool, attempt to communicate with the instrument panel cluster (IPC). Communication should be available.
- Install another 3A fused jumper wire to JX 200 terminal A, harness side.
- With IPC communications established, use the other end of the jumper wire to connect all other terminals, harness side, one at a time and verify that low speed communication remains available to the IPC.
| ⇒ | If greater than the specified range, test the ground circuit for open/high resistance. |
| ⇒ | If no communication, test the serial data circuit for a short to ground, a short to voltage or an open/high resistance between the IPC and the DLC. If the circuit tests normal, replace the IPC. |
Important: Allow communications for 5 seconds after connecting a module with the jumper to determine if communication is interrupted or not.
| ⇒ | If low speed communication is interrupted after connecting an individual module at JX 200, test the serial data circuit between JX 200 and the last module connected for a short to voltage and short to ground. If the circuit tests normal, replace the module that caused no communication. |
Repair Instructions
Perform the Diagnostic Repair Verification after completing the repair.
| • | Control Module References for module replacement, setup, and programming |
