GM Service Manual Online
For 1990-2009 cars only

Air Conditioning Compressor Replacement 4.3L

Special Tools

J 39400-A Halogen Leak Detector

Removal Procedure

  1. Remove the air cleaner assembly. Refer to Air Cleaner Assembly Replacement.
  2. Recover the refrigerant from the A/C system. Refer to Refrigerant Recovery and Recharging.

  3. Object Number: 573938  Size: SH
  4. Disconnect the clutch coil electrical connector (1) from the compressor.

  5. Object Number: 573960  Size: SH
  6. Disconnect the A/C high pressure switch electrical connector (2) from the compressor.
  7. Remove the drive belt. Refer to Drive Belt Replacement.

  8. Object Number: 300811  Size: SH
  9. Remove the compressor hose assembly.
  10. Remove the mounting bolts (2) from the compressor.
  11. Remove the compressor from the vehicle.
  12. If replacing the compressor, balance the refrigerant oil. Refer to Air Conditioning Compressor Oil Balancing.

Installation Procedure


    Object Number: 300811  Size: SH
  1. Install the compressor (1) to the vehicle.
  2. Caution: Refer to Fastener Caution in the Preface section.

  3. Install the compressor retaining bolts to the mounting bracket and tighten to 50 N·m (37 lb ft).
  4. Install the new sealing washers. Refer to Sealing Washer Replacement.
  5. Install the compressor hose assembly.
  6. Install the drive belt. Refer to Drive Belt Replacement.

  7. Object Number: 573938  Size: SH
  8. Connect the clutch coil electrical connector (1) to the compressor.

  9. Object Number: 573960  Size: SH
  10. Connect the A/C high pressure switch electrical connector (2) to the compressor.
  11. Install the air cleaner assembly. Refer to Air Cleaner Assembly Replacement.
  12. Evacuate and recharge the A/C system. Refer to Refrigerant Recovery and Recharging.
  13. Leak test the fittings of the components using the J 39400-A .

Air Conditioning Compressor Replacement 4.8L, 5.3L, 6.0L

Special Tools

J 39400-A Halogen Leak Detector

Removal Procedure

  1. Recover the refrigerant from the A/C system. Refer to Refrigerant Recovery and Recharging.

  2. Object Number: 370869  Size: SH
  3. Remove the engine coolant recovery reservoir. Refer to Coolant Recovery Reservoir Replacement.
  4. Remove the suction hose bolt from the compressor.
  5. Remove the suction hose from the compressor.
  6. Remove the discharge hose bolt from the compressor.
  7. Remove the discharge hose from the compressor.
  8. Loosen the upper compressor mounting bolts and leave bolts in place.
  9. Raise the vehicle. Refer to Lifting and Jacking the Vehicle.
  10. Remove G104 from the frame and reposition ground strap.
  11. Install a ratchet into the A/C belt tensioner adapter opening.
  12. Rotate the belt tensioner clockwise in order to relieve the tension on the belt.
  13. Remove the A/C belt from the pulley.
  14. Disconnect the compressor clutch electrical connector.
  15. Remove the lower compressor mounting bolts.
  16. Reposition the compressor and disconnect the high pressure switch connector.
  17. All wheel drive only, remove the fan and fan shroud. Refer to Engine Coolant Fan Lower Shroud Replacement and Fan Replacement.
  18. Remove the compressor.
  19. Note: When removing the sealing washers, prevent dirt and foreign material from getting onto the following sealing surfaces:

       • The washers
       • The hose fitting
       • The compressor ports
    Use a lint-free cloth in order to clean all of the sealing surfaces.

  20. Remove the compressor sealing washers.
  21. Discard the compressor sealing washers.

    If replacing the compressor, balance the refrigerant oil. Refer to Air Conditioning Compressor Oil Balancing.

Installation Procedure

  1. Install the new sealing washers. Refer to Sealing Washer Replacement.
  2. Connect the high pressure switch connector.
  3. Caution: Refer to Fastener Caution in the Preface section.

  4. Install the compressor with the mounting bolts in the compressor and tighten to 50 N·m (37 lb ft).
  5. Connect the compressor clutch electrical connector.
  6. Install a ratchet into the A/C belt tensioner adapter opening.
  7. Rotate the belt tensioner clockwise in order to install the belt.
  8. Install the A/C belt on to the pulley.
  9. Install G104 to the frame.
  10. Lower the vehicle.
  11. Tighten the upper mounting bolts and tighten to 50 N·m (37 lb ft).
  12. Install the discharge hose to the compressor.
  13. Install the discharge hose bolt to the compressor and tighten to 35 N·m (26 lb ft).
  14. Install the suction hose to the compressor.
  15. Install the suction hose bolt to the compressor and tighten to 35 N·m (26 lb ft).

  16. Object Number: 370869  Size: SH
  17. All wheel drive only, install the fan and fan shroud. Refer to Fan Replacement and Engine Coolant Fan Lower Shroud Replacement.
  18. Install the engine coolant recovery reservoir. Refer to Coolant Recovery Reservoir Replacement.
  19. Evacuate and recharge the A/C system. Refer to Refrigerant Recovery and Recharging.
  20. Leak test the fittings of the component using the J 39400-A .

Air Conditioning Compressor Replacement 6.6L

Special Tools

J 39400-A Halogen Leak Detector

Removal Procedure

  1. Recover the refrigerant. Refer to Refrigerant Recovery and Recharging.
  2. Remove the air cleaner outlet duct. Refer to Air Cleaner Outlet Duct Replacement.
  3. Remove the drive belt. Refer to Drive Belt Replacement.

  4. Object Number: 1652913  Size: SH
  5. Remove the discharge hose bolt (1) from the A/C compressor.
  6. Remove the discharge hose (4) from the A/C compressor.
  7. Remove the suction hose bolt (2) from the A/C compressor.
  8. Remove the suction hose (3) from the A/C compressor.
  9. Discard the sealing washers. Cap all of the openings.
  10. Disconnect the A/C compressor electrical connection.

  11. Object Number: 652574  Size: SH
  12. Remove the A/C compressor mounting bolts.
  13. Remove the A/C compressor from the vehicle.

Installation Procedure

  1. If replacing the A/C compressor, balance the compressor oil. Refer to Air Conditioning Compressor Oil Balancing.

  2. Object Number: 652574  Size: SH
  3. Remove the caps or tape from the hose and line ends.
  4. Install the A/C compressor.
  5. Caution: Refer to Fastener Caution in the Preface section.

  6. Install the A/C compressor mounting bolts and tighten to 50 N·m (37 lb ft).
  7. Connect the A/C compressor electrical connection.
  8. Install new sealing washers on the A/C compressor hoses. Refer to Sealing Washer Replacement.

  9. Object Number: 1652913  Size: SH
  10. Install the A/C discharge hose (4) to the compressor.
  11. Install the A/C discharge hose bolt (1) to the A/C compressor and tighten to 16 N·m (12 lb ft).
  12. Install the A/C suction hose (3) to the compressor.
  13. Install the A/C suction hose bolt (2) to the A/C compressor and tighten to 16 N·m (12 lb ft).
  14. Install the drive belt. Refer to Drive Belt Replacement.
  15. Install the air cleaner outlet duct. Refer to Air Cleaner Outlet Duct Replacement.
  16. Evacuate and recharge the A/C system. Refer to Refrigerant Recovery and Recharging.
  17. Leak test the fittings of the component using the J 39400-A .