GM Service Manual Online
For 1990-2009 cars only

Cooling Fan Always On 2.0

Diagnostic Instructions

    • Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure.
    • Review Strategy Based Diagnosis for an overview of the diagnostic approach.
    •  Diagnostic Procedure Instructions provides an overview of each diagnostic category.

Circuit/System Description

The engine cooling fan is a variable speed fan. The engine control module (ECM) controls the fan speed by sending a pulse width modulated (PWM) signal to the cooling fan control module. The cooling fan control module varies the voltage drop across the engine cooling fan motor in relation to the pulse width modulated signal. The cooling fan speed can be adjusted from 10 percent to 90 percent duty cycle. 90-94 percent is considered high speed fan.

The ECM monitors the voltage on the cooling fan speed control circuit driver output. Voltage is near B+ when the driver is OFF, and near ground when the driver is ON. If the difference between the actual and expected voltage exceeds a calibrated value, a DTC will set.

Reference Information

Schematic Reference

Engine Cooling Schematics

Connector End View Reference

Component Connector End Views

Description and Operation

Cooling Fan Description and Operation

Electrical Information Reference

    •  Circuit Testing
    •  Connector Repairs
    •  Testing for Intermittent Conditions and Poor Connections
    •  Wiring Repairs

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions

Scan Tool Reference

Control Module References for scan tool information

Circuit/System Verification

  1. If DTCs P0480, P0691, or P0692 are set, perform that diagnostic first.
  2. Ignition ON, verify with a scan tool that the ECM is not commanding fan activation.
  3. Ignition ON, observe that the fan is not activated.
  4. If the fan is activated, replace the cooling fan assembly.

Repair Instructions

Perform the Cooling Fan and Shroud Replacement after completing the diagnostic procedure.

Repair Verification

  1. Ignition ON, verify with a scan tool that the ECM is not commanding fan activation.
  2. Ignition ON, observe that the fan is not activated.

Cooling Fan Always On 2.2L or 2.4L

Diagnostic Instructions

    • Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure.
    • Review Strategy Based Diagnosis for an overview of the diagnostic approach.
    •  Diagnostic Procedure Instructions provides an overview of each diagnostic category.

Circuit/System Description

The engine control module (ECM) grounds the relay control circuit through an internal solid state device called a driver. The primary function of the driver is to supply the ground for the component being controlled. Each driver has a fault line that is monitored by the ECM. When the ECM is commanding a component ON, the voltage potential of the control circuit should be low, near 0 volts. When the ECM is commanding the control circuit to a component OFF, the voltage potential of the circuit should be high, near battery voltage. If the ECM detects that the actual state of the control circuit does not match the expected state, a DTC will set.

Reference Information

Schematic Reference

Engine Cooling Schematics

Connector End View Reference

Component Connector End Views

Description and Operation

Cooling Fan Description and Operation

Electrical Information Reference

    •  Circuit Testing
    •  Connector Repairs
    •  Testing for Intermittent Conditions and Poor Connections
    •  Wiring Repairs

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions

Scan Tool Reference

Control Module References for scan tool information

Circuit/System Verification

  1. If DTC P0480 is set, perform that diagnostic first.
  2. Ignition ON, verify with a scan tool that the fan is commanded OFF.
  3. Observe that the fan is OFF.

Circuit/System Testing

  1. Disconnect the cooling fan relay. The fan should be ON.
  2. If the fan is OFF, replace the relay.
  3. If the relay is normal and the fan is ON, test the relay controlled output circuit terminal 87 for a short to voltage.

Repair Instructions

Cooling Fan and Shroud Replacement

Repair Verification

Ignition ON, command the relay ON and OFF with a scan tool. Observe to verify that the fan turns ON and OFF with each command.