The brake pedal position sensor is used to sense the action of the driver application of the brake pedal. The brake pedal position sensor provides an analog voltage signal that will increase as the brake pedal is applied. The body control module (BCM) provides a low reference signal and a 5-volt reference voltage to the brake pedal position sensor. When the variable signal reaches a voltage threshold indicating the brakes have been applied, the BCM will apply battery voltage to the stop lamps, transmission control module (TCM), engine control module (ECM), and center high mounted stop lamp (CHMSL) relay coil. When the CHMSL relay receives battery voltage from the BCM, the relay coil is energized and the CHMSL relay switch contacts close applying battery voltage through the STOP LP fuse to illuminate the CHMSL.

Schematic Reference

Exterior Lights Schematics

Connector End View Reference

Component Connector End Views

Description and Operation

Exterior Lighting Systems Description and Operation

Electrical Information Reference

Scan Tool Reference

Control Module References for scan tool information

1. Ignition ON, observe the scan tool Brake Lamp Cmd. parameter as you apply and unapply the brake pedal. The parameter should change between Off and On as the brake pedal is applied and released.

⇒	If the parameter does not change as the brake pedal is applied and released, refer to Brake Pedal Position Sensor (BPPS) Malfunction.

2. With a scan tool, command the LR Stop/Turn Signal Lamp ON and OFF. The LR turn signal should turn ON and OFF when changing between the commanded states.

⇒	If the LR stop lamp does not illuminate when commanded, refer to Stop Lamps Malfunction.

3. With a scan tool, command the RR Stop/Turn Signal Lamp ON and OFF. The RR turn signal should turn ON and OFF when changing between the commanded states.

⇒	If the RR stop lamp does not illuminate when commanded, refer to Stop Lamps Malfunction.

Stop Lamps Malfunction

1. Ignition OFF, disconnect the harness connector at the inoperative stop lamp.
2. Ignition OFF, exterior lamps OFF, test for less than 5 ohms between the ground circuit terminal C and ground.

⇒	If greater than the specified range, test the ground circuit for an open/high resistance.

3. Connect a test lamp between the control circuit terminal A and ground.
4. Ignition ON, command the appropriate Stop/Turn Signal Lamp ON and OFF with a scan tool. The test lamp should turn ON and OFF when changing between the commanded states.

⇒	If the test lamp is always ON, test the control circuit for a short to voltage. If the circuit tests normal, replace the BCM.

⇒	If the test lamp is always OFF, test the control circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the BCM.

5. If all circuits test normal, replace the inoperative tail lamp assembly.

Center High Mounted Stop Lamp (CHMSL) Malfunction

1. Ignition OFF, disconnect the CHMSL relay.
2. Ignition OFF, exterior lamps OFF, test for less than 5 ohms between the ground circuit terminal 2 and ground.

⇒	If greater than the specified range, test the ground circuit for an open/high resistance.

3. Ignition ON, verify that a test lamp does not illuminate between the control circuit terminal 5 and ground.

⇒	If the test lamp illuminates, test the control circuit for a short to voltage.

4. Verify that a test lamp illuminates between the B+ circuit terminal 3 and ground.

⇒	If the test lamp does not illuminate, test the B+ circuit for a short to ground or an open/high resistance. If the circuit tests normal and the B+ circuit fuse is open, test the control circuit terminal 5 for a short to ground. If the circuit tests normal, test or replace the CHMSL relay.

5. Ignition OFF, disconnect the harness connector at the CHMSL.
6. Ignition OFF, exterior lamps OFF, test for less than 5 ohms between the ground circuit terminal B and ground.

⇒	If greater than the specified range, test the ground circuit for an open/high resistance.

7. Connect the harness connector at the CHMSL.
8. Connect a 10A fused jumper wire between the B+ circuit terminal 3 and the control circuit terminal 5. Verify the CHMSL illuminates.

⇒	If the CHMSL does not illuminate, test the control circuit for an open/high resistance. If the circuit tests normal, replace the CHMSL.

9. Connect a test lamp between the control circuit terminal 1 and ground.
10. Ignition ON, command the stop lamps ON and OFF by applying and releasing the brake pedal. The test lamp should turn ON and OFF when changing between the commanded states.

⇒	If the test lamp is always ON, test the control circuit for a short to voltage. If the circuit tests normal, replace the BCM.

⇒	If the test lamp is always OFF, test the control circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the BCM.

11. If all circuits test normal, test or replace the CHMSL.

Brake Pedal Position Sensor (BPPS) Malfunction

1. Ignition OFF, disconnect the harness connector at the BPPS.
2. Ignition ON, verify that a test lamp does not illuminate between the low reference circuit terminal A and ground.

⇒	If the test lamp illuminates, test the low reference circuit for a short to voltage. If the circuit tests normal, replace the BCM.

3. Ignition ON, test for 4.8 volts and 5.2 volts between the 5-volt reference circuit terminal C and ground.

⇒	If less than the specified range, test the 5-volt reference circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the BCM.

⇒	If greater than the specified range, test the 5-volt reference circuit for a short to voltage. If the circuit tests normal, replace the BCM.

4. If all circuits test normal, replace the BPPS.

Perform the Diagnostic Repair Verification after completing the diagnostic procedure.