Circuit Description
The powertrain control module (PCM) provides 5 volts to the air conditioning (A/C) pressure sensor. The PCM monitors the voltage on the 5-volt reference circuit. If the PCM detects that the voltage is out of tolerance, DTC P0651 sets.
DTC Descriptor
This diagnostic procedure supports the following DTC:
DTC P0651 5-Volt Reference 2 Circuit
Conditions for Running the DTC
The ignition is ON.
Conditions for Setting the DTC
| • | The 5-volt reference 2 voltage is more than 4.7 volts or less than 4.4 volts for longer than 10 seconds. |
| • | This diagnostic runs continuously. |
Action Taken When the DTC Sets
| • | The control module illuminates the malfunction indicator lamp (MIL) on the second consecutive ignition cycle that the diagnostic runs and fails. |
| • | The control module records the operating conditions at the time the diagnostic fails. The first time the diagnostic fails, the control module stores this information in the Failure Records. If the diagnostic reports a failure on the second consecutive ignition cycle, the control module records the operating conditions at the time of the failure. The control module writes the operating conditions to the Freeze Frame and updates the Failure Records. |
Conditions for Clearing the MIL/DTC
| • | The control module turns OFF the malfunction indicator lamp (MIL) after 3 consecutive ignition cycles that the diagnostic runs and does not fail. |
| • | A current DTC, Last Test Failed, clears when the diagnostic runs and passes. |
| • | A history DTC clears after 40 consecutive warm-up cycles, if no failures are reported by this or any other emission related diagnostic. |
| • | Clear the MIL and the DTC with a scan tool. |
Diagnostic Aids
| • | If any sensor using a 5-volt bias voltage, such as the intake air temperature (IAT) sensor or fuel sensor, is shorted to voltage, DTC P0651 may set in addition to DTC P0641. |
| • | For an intermittent condition, refer to Intermittent Conditions. |
Step | Action | Values | Yes | No |
|---|---|---|---|---|
Schematic Reference: Instrument Cluster Schematics in Instrument Panel, Gages, and Console or Engine Controls Schematics Connector End View Reference: Instrument Panel, Gages, and Console Component Views , and Instrument Panel, Gages, and Console Connector End Views in Instrument Panel, Gages, and Console or Powertrain Control Module Connector End Views | ||||
1 | Did you perform the Diagnostic System Check - Vehicle? | -- | Go to Step 2 | Go to Diagnostic System Check - Vehicle in Vehicle DTC Information |
2 |
Did the DTC fail this ignition? | -- | Go to Step 3 | Go to Diagnostic Aids |
3 |
Is the voltage within the specified range? | 4.8-5.2 V | Go to Step 7 | Go to Step 4 |
4 | Is the voltage measured in the previous step more than the specified value? | 5.2 V | Go to Step 5 | Go to Step 6 |
5 | Test the 5-volt reference circuit for a short to voltage. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 9 | Go to Step 8 |
6 | Test the 5-volt reference circuit for a short to ground or any sensor low reference circuit. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 9 | Go to Step 8 |
7 | Replace the A/C refrigerant pressure sensor. Refer to Air Conditioning (A/C) Refrigerant Pressure Sensor Replacement in Heating, Ventilation, and Air Conditioning. Did you complete the replacement? | -- | Go to Step 9 | -- |
8 | Replace the PCM. Refer to Control Module References in Computer/Integrating Systems for replacement, setup, and programming. Did you complete the replacement? | -- | Go to Step 9 | -- |
9 |
Did the DTC fail this ignition? | -- | Go to Step 2 | Go to Step 10 |
10 | Observe the Capture Info with a scan tool. Are there any DTCs that have not been diagnosed? | -- | Go to Diagnostic Trouble Code (DTC) List - Vehicle in Vehicle DTC Information | System OK |
