Definition: Engine power variation under steady throttle or cruise. Feels like the vehicle speeds up and slows down with no change in the accelerator pedal.

Was the Powertrain On-Board Diagnostic (OBD) System Check performed?

--

Go to Step 2

Go to the Powertrain On Board Diagnostic (OBD) System Check

1. Perform a bulletin search.
2. If a bulletin that addresses the symptom is found, correct the condition as instructed in the bulletin.

Was a bulletin found that addresses the symptom?

--

Go to Step 22

Go to Step 3

Was visual/physical check performed?

--

Go to Step 4

Go to Visual/Physical Checks

Be sure driver understands Transaxle torque converter clutch and A/C compressor operation as explained in the owner's manual. Inform customer how TCC and the A/C clutch operates.

Is the customer experiencing a normal condition?

--

System OK

Go to Step 5

1. Check Heated Oxygen Sensors (HO2S). The Heated Oxygen Sensors (HO2S) should respond quickly to different throttle position. If they don't, check the HO2S for silicon or other contaminants from fuel or use of improper RTV sealant. The sensors may have a white powdery coating. Silicon contamination causes in a high but false HO2S signal voltage (rich exhaust indication). The PCM will then reduce the amount of fuel delivered to the engine , causing a severe driveability problem. For more information, refer to Information Sensors .
2. If a problem is found, repair as necessary.

Was a repair required?

--

Go to Step 22

Go to Step 6

1. Check fuel pressure. Refer to Fuel System Pressure Test .
2. If a problem is found, repair as necessary.

Was a problem found?

--

Go to Step 22

Go to Step 7

Monitor Long Term Fuel Trim on the scan tool.

Is Long Term Fuel Trim significantly in the negative range (Rich condition)?

--

Go to Step 8

Go to Step 9

1. Check items that can cause the engine to run rich. Refer to DTC P0172 Fuel Trim System Rich .
2. If a problem is found, repair as necessary.

Was a problem found?

--

Go to Step 10

Go to Step 22

1. Check items that can cause the engine to run lean. Refer to DTC P0171 Fuel Trim System Lean .
2. If a problem is found, repair as necessary.

Was a problem found?

--

Go to Step 10

Go to Step 22

1. Check for proper ignition coil output voltage with spark tester J 26792 :

-	Clip the spark tester to engine ground.

-	Connect one end of a spark plug wire to the spark tester; connect the other end of the spark plug wire to the coil being tested.

-	Connect one end of another spark plug wire to the other coil tower; connect the other end of the spark plug wire to ground.

-	Crank the engine while observing the spark tester; a crisp blue spark should be observed.

-	Repeat the above steps for each coil.

2. If adequate spark is not present at all coils, repair as necessary.

Was a problem found?

--

Go to Step 22

Go to Step 11

1. Check for loose ignition control module ground.
2. If a problem is found, repair as necessary.

Was a problem found?

--

Go to Step 22

Go to Step 12

1. Visually/Physically inspect secondary ignition wires. Check for the following conditions:

•	Check all Ignition wire resistances; should be less than the specified value.

•	Ignition wires for cross firing.

•	Ignition wires arcing to ground.

•	Ignition wires for improper routing.

Important: Spraying the secondary ignition wires with a light mist of water may help locate an intermittent problem. Ignition components will arc to ground when a secondary component is faulty.

1. If a problem is found, repair as necessary.

Was a problem found?

30K ohms (30,000 ohms)

Go to Step 22

Go to Step 13

1. Check ignition coils for cracks or carbon tracking.
2. If a problem is found, repair as necessary.

Was a problem found?

--

Go to Step 22

Go to Step 14

1. Check ignition coil secondary resistance.
2. Replace any coil(s) which are not within the specified values. Refer to Ignition Control Module Replacement .

Did any coil(s) require replacement?

5000-8000 ohms (5K-8 K ohms)

Go to Step 22

Go to Step 15

1. Remove spark plugs and check for wet plugs, cracks, wear, improper gap, burned electrodes, or heavy deposits.

Notice: Determine the cause of the oil or gas fouled spark plugs in order to avoid damage to the new spark plugs.

1. If a problem is found, repair as necessary.

Was a problem found?

--

Go to Step 22

Go to Step 16

1. Check the injector connections.
2. If any of the injector connectors are connected to an incorrect cylinder, correct as necessary.

Was a problem found?

--

Go to Step 22

Go to Step 17

1. Check PCM grounds for being clean, tight and in the proper locations. Refer to Engine Controls Schematics .
2. If a problem is found, repair as necessary.

Was a problem found?

--

Go to Step 22

Go to Step 18

1. Check MAF sensor connections.
2. If a problem is found, replace faulty terminals as necessary. Refer to Repair Procedures in Electrical Diagnosis.

Was a problem found?

--

Go to Step 22

Go to Step 19

1. Visually/physically check vacuum hoses for splits, kinks, and proper connections and routing. Refer to Emission Hose Routing Diagram .
2. If a problem is found, repair as necessary.

Was a problem found?

--

Go to Step 22

Go to Step 20

1. Check exhaust system for possible restriction:

•	Inspect exhaust system for damaged or collapsed pipes.

•	Inspect muffler for heat distress or possible internal failure.

•	Check for a possible plugged three-way catalytic converter by checking exhaust system back pressure.

•	Refer to Restricted Exhaust System Check .

2. If a problem is found, repair as necessary.

Was a problem found?

--

Go to Step 22

Go to Step 21

1. Review all diagnostic procedures within this table.
2. If all procedures have been completed and no malfunctions have been found, review/inspect the following:

•	Visual/physical inspection.

•	Scan Tool data.

•	Freeze Frame data/Failure Records Data.

•	All electrical connections within a suspected circuit and/or system.

3. If a problem is found, repair as necessary.

Was a problem found?

--

Go to Step 22

Refer to Technical Service Bulletins

Operate the vehicle to duplicate conditions present when the original symptom was noted.

Is symptom still present?

--

Go to Step 3

System OK