Engine Coolant Thermostat Housing Replacement LZ4

1. Drain the cooling system. Refer to Cooling System Draining and Filling.
2. Remove the air cleaner outlet duct. Refer to Air Cleaner Outlet Duct Replacement.
3. Reposition the radiator outlet hose clamp at the thermostat housing.
4. Remove the radiator outlet hose from the thermostat housing.



5. Remove the thermostat housing bolt/stud.
6. Remove the thermostat housing and gasket.
7. Clean the gasket surfaces.

1. Position a NEW gasket and the thermostat housing to the engine block.

Notice: Refer to Fastener Notice in the Preface section.

2. Install the thermostat housing bolt/stud.

Tighten
Tighten the bolt/stud to 10 N·m (89 lb in).




3. Install the radiator outlet hose to the thermostat housing.
4. Position the radiator outlet hose clamp at the thermostat housing.
5. Install the air cleaner outlet duct. Refer to Air Cleaner Outlet Duct Replacement.
6. Fill the cooling system. Refer to Cooling System Draining and Filling.
7. Inspect the system for leaks.

Engine Coolant Thermostat Housing Replacement LAT

1. Drain the cooling system. Refer to Cooling System Draining and Filling .

Important: A drain has been provided at the bottom of the water pump for engine block coolant drainage.

2. Drain the coolant from the engine block at the water pump drain. After the coolant has drained, tighten the drain bolt.
3. Lower the vehicle.
4. Remove the battery tray. Refer to Battery Tray Replacement .



5. Disconnect the engine wiring harness electrical connector (1) from the engine coolant temperature (ECT) sensor.
6. Remove the heated oxygen sensor (HO2S) electrical connector rosebud clip from the thermostat housing.



7. Reposition the radiator outlet hose clamp at the thermostat cover.
8. Remove the radiator outlet hose from the thermostat cover.



9. Remove the exhaust heat shield bolts (1).
10. Remove the exhaust heat shield.



11. Remove the auxiliary heater water pump hose clip (1) from the heater outlet hose.
12. Reposition the auxiliary heater water pump hose clamp at the thermostat housing.
13. Remove the auxiliary heater water pump hose (2) from the thermostat housing.
14. Reposition the heater inlet hose clamp at the thermostat housing.
15. Remove the heater inlet hose (3) from the thermostat housing.
16. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle .



17. Remove the ECT sensor, if necessary.



18. Remove the thermostat housing bolts.

Important: Twist the water transfer pipe while pulling in order to remove it from the water pump.

19. Remove the thermostat from the vehicle.
20. Remove the water transfer pipe from the thermostat housing, if necessary.
21. Remove and discard the water transfer pipe O-ring seals, if necessary.



22. Remove the thermostat cover bolts and cover, if necessary.
23. Remove the thermostat, if necessary.
24. Remove and discard the thermostat cover O-ring seal, if necessary.
25. Remove all debris and thread sealant from the engine coolant temperature (ECT) sensor and bolt holes if the housing is being re-used.

1. Install a NEW thermostat cover O-ring seal into the recess groove.
2. Install the thermostat, if necessary.

Notice: Refer to Fastener Notice in the Preface section.

3. Install the thermostat cover bolts, if necessary.

Tighten
Tighten the bolts to 10 N·m (89 lb in).

4. Install a NEW thermostat housing to engine gasket onto the thermostat housing.
5. Load the thermostat housing assembly into position.




Important: The water feed pipe seals can be lightly lubricated with coolant to aid during installation.

6. Install NEW O-ring seals onto the water feed pipe.

Important: Lubricate the O-rings with coolant ONLY.

7. Install the water feed pipe into the thermostat housing aligning locator tab.
8. Align the water pipe to water pump.
9. Seat the water feed O-ring seal by pushing inward toward the water pump. Take care not to tear or damage the O-ring.
10. Position the thermostat housing against the engine.
11. Install the thermostat housing bolts.

Tighten
Tighten the bolts to 10 N·m (89 lb in).




12. If reinstalling the old sensor, coat the threads with sealant. Refer to Adhesives, Fluids, Lubricants, and Sealers .
13. Install the ECT sensor, if necessary.

Tighten
Tighten the sensor to 20 N·m (15 lb ft).

14. Lower the vehicle.



15. Install the heater inlet hose (3) to the thermostat housing.
16. Position the heater inlet hose clamp at the thermostat housing.
17. Install the auxiliary heater water pump hose (2) to the thermostat housing.
18. Position the auxiliary heater water pump hose clamp at the thermostat housing.
19. Install the auxiliary heater water pump hose clip (1) to the heater outlet hose.



20. Install the exhaust heat shield.
21. Install the exhaust heat shield bolts.

Tighten
Tighten the studs to 22 N·m (16 lb ft).




22. Install the radiator outlet hose to the thermostat cover.
23. Position the radiator outlet hose clamp at the thermostat cover.



24. Connect the engine wiring harness electrical connector (1) to the ECT sensor.
25. Install the HO2S electrical connector rosebud clip to the thermostat housing.
26. Install the battery tray. Refer to Battery Tray Replacement .



27. Verify the drain valves at the radiator and water pump are closed.
28. Lower the vehicle.
29. Fill the cooling system. Refer to Cooling System Draining and Filling .

Engine Coolant Thermostat Housing Replacement LE5

1. Drain the cooling system. Refer to Cooling System Draining and Filling .

Important: A drain has been provided at the bottom of the water pump for engine block coolant drainage.

2. Remove the water pump drain plug and drain the coolant from the engine block at the water pump drain.
3. Lower the vehicle.



4. Disconnect the engine coolant temperature (ECT) sensor electrical connector (1).
5. Disconnect the heated oxygen sensor (HO2S) electrical connector clip from the bracket.



6. Remove the ECT sensor.
7. Remove the surge tank outlet hose from the thermostat housing.



8. Reposition the radiator outlet hose clamp at the thermostat housing.
9. Remove the radiator outlet hose from the thermostat housing.



10. Remove the exhaust heat shield bolts.
11. Remove the exhaust heat shield.



12. Reposition the heater inlet and outlet hose clamps at the thermostat housing pipes.
13. Disconnect the heater inlet (1) and outlet (2) hoses from the thermostat housing pipes.



14. Remove the thermostat housing bolts.

Important: Twist the water transfer pipe while pulling in order to remove it from the water pump.

15. Remove the thermostat housing from the vehicle.
16. Remove the water transfer pipe from the thermostat housing, if necessary.
17. Remove and discard the water transfer pipe O-ring seals, if necessary.



18. Remove the thermostat housing cover bolts and cover, if necessary.
19. Remove the thermostat, if necessary.
20. Remove and discard the thermostat housing O-ring seal, if necessary.
21. Remove all debris and thread sealant from the engine coolant temperature sensor and bolt holes if the housing is being re-used.

1. Install a NEW thermostat housing cover O-ring seal into the recess groove.
2. Install the thermostat, if necessary.

Notice: Refer to Fastener Notice in the Preface section.

3. Install the thermostat housing cover bolts, if necessary.

Tighten
Tighten the bolts to 10 N·m (89 lb in).

4. Install a NEW thermostat housing to engine O-ring seal onto the thermostat housing.
5. Load the thermostat housing assembly into position while the vehicle is lowered.




Important: The water feed pipe seals can be lightly lubricated with coolant to aid during installation.

6. Install NEW O-ring seals onto the water feed pipe.

Important: Lubricate the O-rings with coolant ONLY.

7. Install the water feed pipe into the thermostat housing aligning locator tab.
8. Align the water pipe to water pump.
9. Seat the water feed O-ring seal by pushing inward toward the water pump. Take care not to tear or damage the O-ring.
10. Position the thermostat housing against the engine.
11. Install the thermostat housing bolts.

Tighten
Tighten the bolts to 10 N·m (89 lb in).




12. Connect the heater inlet (1) and outlet (2) hoses to the thermostat housing pipes.
13. Position the heater inlet and outlet hose clamps at the thermostat housing pipes.



14. Install the exhaust heat shield.
15. Install the exhaust heat shield bolts.

Tighten
Tighten the bolts to 23 N·m (17 lb ft).




16. Install the radiator outlet hose to the thermostat housing.
17. Position the radiator outlet hose clamp at the thermostat housing.



18. Install the radiator outlet hose to the surge tank.
19. Position the radiator outlet hose clamp at the surge tank.



20. Apply sealant to the threads of the ECT sensor. Refer to Adhesives, Fluids, Lubricants, and Sealers .
21. Install the ECT sensor.

Tighten
Tighten the sensor to 20 N·m (15 lb ft).




22. Connect the ECT sensor electrical connector (1).
23. Connect the HO2S electrical connector clip to the bracket.



24. Apply sealant GM P/N 12378521 (Canadian P/N 88901148) or equivalent to the water pump drain plug.
25. Install the water pump drain plug.

Tighten
Tighten the drain plug to 20 N·m (15 lb ft).

Important: The vehicle must be level when filling the cooling system.

26. Verify the drain valves at the radiator and water pump are closed.
27. Fill the cooling system. Refer to Cooling System Draining and Filling .
28. Verify the repair and inspect for any leaks.

Engine Coolant Thermostat Housing Replacement LY7

1. Partially drain the cooling system. Refer to Cooling System Draining and Filling.
2. Remove the air cleaner outlet duct. Refer to Air Cleaner Outlet Duct Replacement
3. Remove the radiator outlet hose from the thermostat housing.
4. Remove the heater inlet and outlet hoses.
5. Remove the surge tank outlet hose.
6. Remove the thermostat housing bolts (1).
7. Remove the housing.

Notice: Refer to Fastener Notice in the Preface section.




1. Install the thermostat housing bolts.

Tighten
Tighten the thermostat housing bolts to 10 N·m (89 lb in).

2. Install the surge tank outlet hose.
3. Install the heater inlet and outlet hoses.
4. Install the radiator outlet hose to the thermostat housing.
5. Install the air cleaner outlet duct. Refer to Air Cleaner Outlet Duct Replacement
6. Fill the cooling system. Refer to Cooling System Draining and Filling.