Step | Action | Yes | No |
|---|---|---|---|
Schematic Reference: Door Lock/Indicator Schematics Connector End View Reference: Vehicle Access Connector End Views DEFINITION: One or all 3 of the passenger door lock actuators do not operate, or, the front passenger door lock switch does not operate. | |||
1 | Did you perform the Diagnostic System Check - Vehicle? | Go to Step 2 | |
2 | Verify that the Power Door Locks Inoperative - Passenger Door fault is present. Do the door locks operate as described in the Power Door Locks Description and Operation? | Go to Testing for Intermittent Conditions and Poor Connections | Go to Step 3 |
3 | If the vehicle is a 4-door model, are all 3 of the passenger doors locks inoperative from both door lock switches? | Go to Step 10 | Go to Step 4 |
4 |
Did the parameter change to both the LOCK and UNLOCK states? | Go to Step 7 | Go to Step 5 |
5 |
Important: If the 3-amp fuse of the jumper wire opens when the jumper wire is connected, test the appropriate signal circuit for a short to battery positive voltage.
Did the Scan Tool parameter change to the both the LOCK and UNLOCK states? | Go to Step 6 | Go to Step 8 |
6 | Connect the 3-amp fused jumper wire between the lock switch lock signal circuit and the ground circuit of the harness connector while observing the appropriate Scan Tool parameter. Did the Scan Tool parameter change to the LOCK state? | Go to Step 11 | Go to Step 14 |
7 |
Did the test lamp illuminate in both positions? | Go to Step 13 | Go to Step 9 |
8 | Test the signal circuits of the front passenger door lock switch for a short to ground or an open. Refer to Circuit Testing and Wiring Repairs . Did you find and correct the condition? | Go to Step 18 | Go to Step 12 |
9 | Test the lock control circuit of the inoperative door lock actuator for an open. Refer to Circuit Testing and Wiring Repairs . Did you find and correct the condition? | Go to Step 18 | Go to Step 10 |
10 |
Important: If all 3 passenger door locks are inoperative from both door lock switches, test the unlock control circuit between the splice and the BCM for an open. Test the unlock control circuit of the inoperative door lock actuator for an open. Refer to Circuit Testing and Wiring Repairs . Did you find and correct the condition? | Go to Step 18 | Go to Step 12 |
11 | Inspect for poor connections at the harness connector of the front passenger door lock switch. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs . Did you find and correct the condition? | Go to Step 18 | Go to Step 15 |
12 | Inspect for poor connections at the harness connector of the BCM. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs . Did you find and correct the condition? | Go to Step 18 | Go to Step 16 |
13 | Inspect for poor connections at the harness connector of the inoperative door lock actuator. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs . Did you find and correct the condition? | Go to Step 18 | Go to Step 17 |
14 | Repair the open ground circuit of the front passenger door lock switch. Refer to Circuit Testing and Wiring Repairs . Did you complete the repair? | Go to Step 18 | -- |
15 | Replace the front passenger door lock switch. Refer to Door Lock Switch Replacement . Did you complete the replacement? | Go to Step 18 | -- |
16 | Replace the BCM. Refer to Control Module References for replacement, setup, and programming. Did you complete the replacement? | Go to Step 18 | -- |
17 | Replace the inoperative door lock actuator. Refer to Front Side Door Lock Actuator Replacement or Rear Side Door Lock Actuator Replacement . Did you complete the replacement? | Go to Step 18 | -- |
18 | Operate the system in order to verify the repair. Did you correct the condition? | System OK | Go to Step 2 |
