Cylinder Head Replacement Left

1. Disconnect the battery negative cable. Refer to Battery Replacement .
2. Drain the engine coolant. Refer to Cooling System Draining and Filling .
3. Disconnect the PCV tube from the air cleaner outlet duct.
4. Remove the air cleaner outlet duct from the throttle body.
5. Remove the air cleaner assembly. Refer to Air Cleaner Assembly Replacement .
6. Remove the engine cooling fan assembly. Refer to Fan Clutch Replacement .

Important: Do not evacuate the A/C system. The A/C pipes can remain on the compressor.

7. Remove the air conditioning compressor, if equipped, and move aside. Refer to Air Conditioning Compressor Replacement .



8. Remove the nuts holding the power steering pump rear bracket to the engine.




Important: The power steering pump can remain on the power steering pump mounting bracket. The power steering pump hoses can remain attached to the power steering pump.

9. Remove the power steering pump mounting bracket and secure out of the way.
10. Remove the power steering pump mounting bracket stud from the cylinder head.
11. Remove the intake manifold. Refer to Intake Manifold Replacement
12. Remove the exhaust manifold. Refer to Exhaust Manifold Replacement



13. Remove the spark plug wire harness and the support.



14. Remove the ground wires at the rear of the cylinder head.
15. Remove the fuel line bracket bolt at the rear of the cylinder head.
16. Remove the valve pushrods. Refer to Valve Rocker Arm and Push Rod Replacement



17. Remove and discard the cylinder head bolts.
18. Remove the cylinder head.
19. Clean all surfaces. Refer to Cylinder Head Cleaning and Inspection

1. Install the cylinder head. Refer to Cylinder Head Installation
2. Install the valve pushrods. Refer to Valve Rocker Arm and Push Rod Replacement

Notice: Refer to Fastener Notice in the Preface section.




3. Install the spark plug wire harness and the support.

Tighten
Tighten the support bolts to 12 N·m (106 lb in).




4. Install the ground wires at the rear of the cylinder head.

Tighten
Tighten the ground wire bolt to 35 N·m (26 lb ft).

5. Install the fuel pipe bracket bolt at the rear of the cylinder head.

Tighten
Tighten the fuel pipe bracket bolt to 30 N·m (22 lb ft).

6. Install the exhaust manifold. Refer to Exhaust Manifold Replacement
7. Install the intake manifold. Refer to Valve Rocker Arm Cover Replacement



8. Install the power steering pump mounting bracket stud in the cylinder head.

Tighten
Tighten the power steering pump mounting bracket stud to 20 N·m (15 lb ft).

9. Install the power steering pump mounting bracket.

Tighten
Tighten the power steering pump mounting bracket bolts and nuts to 41 N·m (30 lb ft).




10. Install the nuts holding the power steering pump rear bracket to the engine.

Tighten
Tighten the power steering pump rear bracket nuts to 41 N·m (30 lb ft).

11. Install the air conditioning compressor, if equipped. Refer to Air Conditioning Compressor Replacement .
12. Install the engine cooling fan. Refer to Fan Clutch Replacement in Engine Cooling.



13. Fill the engine coolant system. Refer to Cooling System Draining and Filling .
14. Connect the battery negative cable. Refer to Battery Replacement .
15. Install the air cleaner assembly. Refer to Air Cleaner Assembly Replacement .
16. Install the air cleaner outlet duct onto the throttle body.
17. Connect the PCV tube to the air cleaner outlet duct.

Cylinder Head Replacement Right

1. Disconnect the battery negative cable. Refer to Battery Replacement .
2. Drain the engine coolant. Refer to Cooling System Draining and Filling .
3. Disconnect the PCV tube form the air cleaner outlet duct.
4. Remove the air cleaner outlet duct from the throttle body.
5. Remove the air cleaner assembly. Refer to Air Cleaner Assembly Replacement .
6. Remove the engine cooling fan assembly. Refer to Fan Clutch Replacement .
7. Remove the intake manifold. Refer to Intake Manifold Replacement
8. Remove the exhaust manifold. Refer to Exhaust Manifold Replacement



9. Remove the spark plug wire harness and the support.



10. Remove the ground wires at the rear of the cylinder head.



11. Remove the generator. Refer to Generator Replacement .
12. Remove the generator mounting bracket.
13. Remove the generator mounting bracket stud from the cylinder head.
14. Remove the valve pushrods. Refer to Valve Rocker Arm and Push Rod Replacement .



15. Remove and discard the cylinder head bolts.
16. Remove the cylinder head.
17. Clean all surfaces. Refer to Cylinder Head Cleaning and Inspection .

1. Install the cylinder head. Refer to Cylinder Head Installation .
2. Install the valve pushrods. Refer to Valve Rocker Arm and Push Rod Replacement .

Notice: Refer to Fastener Notice in the Preface section.




3. Install the spark wire harness and support.

Tighten
Tighten the support bolts to 12  N·m (106 lb in).




4. Install the ground wires at the rear of the cylinder head.

Tighten
Tighten the ground wire stud to 35 N·m (26 lb ft).

5. Install the exhaust manifolds. Refer to Exhaust Manifold Replacement .
6. Install the intake manifold. Refer to Intake Manifold Replacement .



7. Install the generator mounting bracket stud to the cylinder head.

Tighten
Tighten the stud to 20  N·m (15 lb ft).

8. Install the generator mounting bracket.

Tighten
Tighten the generator mounting bracket bolts and nuts to 41 N·m (30 lb ft).

9. Install the generator. Refer to Generator Replacement
10. Install the engine cooling fan. Refer to Fan Clutch Replacement .



11. Fill the engine coolant system. Refer to Cooling System Draining and Filling .
12. Connect the battery negative cable. Refer to Battery Replacement .
13. Install the air cleaner assembly. Refer to Air Cleaner Assembly Replacement .
14. Install the air cleaner outlet duct onto the throttle body.
15. Connect the PCV tube to the air cleaner outlet duct.