GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Chevrolet 🢒 2003 🢒 Tracker - 2WD 🢒 Engine 🢒 Engine Mechanical - 2.5L (LE8) 🢒 Cylinder Head Replacement - Right Side

Removal Procedure
  1. Remove the camshafts. Refer to Camshaft Replacement - Right Side .
  2. Remove the lifters. Refer to Valve Lifter Replacement - Right Side .
  3. Remove the exhaust manifold. Refer to Exhaust Manifold Replacement in Engine Exhaust.
  4. Remove the water crossover pipe. Refer to Engine Coolant Crossover Pipe Replacement .

    5. Object Number: 648377 Size: SH
  5. Remove the hex bolt (1).
  6. Remove the cylinder head bolts in the proper order.
  7. Remove the cylinder heads.
  8. Clean the cylinder head mating surface.
  9. Clean the cylinder block mating surface.
  10. Clean the cylinder head bolt threads and bolts. Replace any stretched or damaged bolts.
  11. Clean the cylinder block bolt holes of all debris, threadlocker, sealant etc. Installing a bolt to a blocked bolt hole will cause incorrect torque and may cause cylinder head/block damage.

Installation Procedure

    Object Number: 650453 Size: SH
  1. Install the knock pin (3) to the cylinder block.
  2. Apply sealant (2), GM P/N 12346240, to the cylinder head gasket (1) as shown.
  3. Install the cylinder head gasket to the block with the 86FA mark facing up.
  4. Install the cylinder head to the block.

    5. Object Number: 648380 Size: SH

    Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

    Notice: In order to prevent warpage of the cylinder head, follow the sequence shown whenever removing or installing the head.

    Important: The cylinder head bolts must be torqued in 2 stages, loosened, and then retorqued in 3 stages in order to ensure against compression and coolant leaks.

  5. Apply clean engine oil to the bolt threads and install the cylinder head bolts.

    6. Tighten
    Tighten the cylinder head bolts in the sequence shown to 53 N·m (38.5 lb ft).

  6. Tighten the cylinder head bolts.

    7. Tighten
    Tighten the cylinder head bolts in the sequence shown to 84 N·m (61 lb ft).

  7. Loosen the cylinder head bolts in the reverse order to 0 torque.
  8. Tighten the cylinder head bolts.

    9. Tighten
    Tighten the cylinder head bolts in the sequence shown to 53 N·m (38.5 lb ft).

  9. Tighten the cylinder head bolts.

    10. Tighten
    Tighten the cylinder head bolts in the sequence shown to 84 N·m (61 lb ft).

  10. Tighten the cylinder head bolts.

    11. Tighten
    Tighten the cylinder head bolts in the sequence shown to 105 N·m (76 lb ft).

  11. Install the hex bolt (1).

    12. Tighten
    Tighten the bolt to 11 N·m (7.5 lb ft).

  12. Install the water crossover pipe. Refer to Engine Coolant Crossover Pipe Replacement .
  13. Install the exhaust manifold. Refer to Exhaust Manifold Replacement .
  14. Install the lifters. Refer to Valve Lifter Replacement - Right Side .
  15. Install the camshafts. Refer to Camshaft Replacement - Right Side .