GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 GMC_Truck 🢒 2000 🢒 GMC C Pickup - 2WD 🢒 Body and Accessories 🢒 Doors 🢒 Rear Release Inoperative with Transmitter

Rear Release Inoperative with Transmitter Except Luxury

Step

Action

Value(s)

Yes

No

DEFINITION: This diagnostic procedure should only be used if the liftgate window release operates from the liftgate release switch and is inoperative with the keyless entry transmitter.

1

Was the Keyless Entry System Check performed?

--

Go to Step 2

Go to Remote Keyless Entry System Check

2
  1. Disconnect the remote control door lock receiver connector.
  2. Connect a J 39200 DMM between cavity F and ground.

Is battery voltage present?

--

Go to Step 3

Go to Step 5

3

Connect a DMM between cavity G and the liftgate release switch cavity D.

Is there continuity?

--

Go to Step 4

Go to Step 6

4

Replace the remote control door lock receiver. Refer to Remote Control Door Lock Receiver Replacement .

Is the repair complete?

--

Go to Remote Keyless Entry System Check

--

5

Repair open in CKT 640 (ORN) between remote control door lock receiver and I/P fuse block. Refer to Wiring Repairs in Wiring Systems.

Is the repair complete?

--

Go to Remote Keyless Entry System Check

--

6

Repair open in CKT 1576 (BLK) between remote control door lock receiver and S165. Refer to Wiring Repairs in Wiring Systems.

Is the repair complete?

--

Go to Remote Keyless Entry System Check

--

Rear Release Inoperative with Transmitter Luxury

Step

Action

Value(s)

Yes

No

DEFINITION: This diagnostic procedure should only be used if the liftgate window release operates from the liftgate release switch and is inoperative with the keyless entry transmitter.

1

Was the Keyless Entry System Check performed?

--

Go to Step 2

Go to Remote Keyless Entry System Check

2
  1. Access and disconnect the Liftgate release relay.
  2. Connect aJ 39200 DMM between cavity 5 and ground.

Is there battery voltage?

--

Go to Step 3

Go to Step 7

3

Connect a DMM between cavity 2 and ground.

Is there continuity?

--

Go to Step 4

Go to Step 8

4

Connect a DMM between cavity 3 and connector C221 cavity A.

Is there continuity?

--

Go to Step 5

Go to Step 9

5
  1. Connect a test lamp between cavity 1 and ground.
  2. Press the rear release button on the keyless entry transmitter twice.

Did the test lamp illuminate?

--

Go to Step 6

Go to Step 10

6

Replace the liftgate release relay.

Is the repair complete?

--

Go to Remote Keyless Entry System Check

--

7

Repair the open in CKT 640 (ORN) between the liftgate release relay and the I/P fuse block. Refer to Wiring Repairs in Wiring Systems.

Is the repair complete?

--

Go to Remote Keyless Entry System Check

--

8

Repair the open in CKT 150 (BLK) between the liftgate release relay and G400. Refer to Wiring Repairs in Wiring Systems.

Is the repair complete?

--

Go to Remote Keyless Entry System Check

--

9

Repair the open in CKT 1576 (BLK) between the liftgate release relay and S404. Refer to Wiring Repairs in Wiring Systems.

Is the repair complete?

--

Go to Remote Keyless Entry System Check

--

10
  1. Inspect for an open in CKT 253 (BRN) between the liftgate release relay and the body control module.
  2. Repair as necessary. Refer to Wiring Repairs in Wiring Systems.
  3. If no open was found, replace the body control module. Refer to Body Control Module Replacement in Body Control System.

Is the repair complete?

--

Go to Remote Keyless Entry System Check

--