GM Service Manual Online
For 1990-2009 cars only

Removal Procedure


    Object Number: 1653035  Size: SH
  1. Remove the intake manifold cover. Refer to Intake Manifold Cover Replacement .
  2. Remove the air cleaner outlet duct. Refer to Air Cleaner Outlet Duct Replacement .
  3. Using a pick or a small flat-bladed screwdriver, remove and discard the quick connect fitting clip from the charged air cooler outlet duct.
  4. Remove the charged air cooler outlet duct from the intake.
  5. Remove the exhaust gas recirculation (EGR) cooler tube. Refer to Exhaust Gas Recirculation Valve Cooler Replacement .
  6. Remove the heater outlet hose bolt from the bracket.
  7. Position the heater outlet hose out of the way.

  8. Object Number: 1601448  Size: SH
  9. Remove the wiring harness retainer from the bracket.
  10. Remove the oil level indicator tube bolt.
  11. Remove the oil level indicator tube bracket bolts.
  12. Remove the bracket.

  13. Object Number: 1602054  Size: SH
  14. Remove the fuel filter bracket bolts.
  15. Reposition the fuel filter with bracket.
  16. Remove the positive crankcase ventilation (PCV) hose/pipe. Refer to Positive Crankcase Ventilation Hose/Pipe/Tube Replacement .

  17. Object Number: 1335614  Size: SH
  18. Prior to removing the fuel injector pipes, use compressed air to blow any debris from between the injector line and fittings. Wipe the fittings clean of debris.
  19. Spray lithium grease between the fuel injector line and fittings to assist in containing any debris during removal. Refer to Adhesives, Fluids, Lubricants, and Sealers for the correct part number.
  20. Notice: DO NOT use compressed air to clean debris from the fuel injector inlet after the fuel line is removed. Using compressed air can allow debris to enter the fuel injector inlet and damage the fuel injector.

  21. Remove the right fuel injector pipes.

  22. Object Number: 1335653  Size: SH
  23. Remove the upper valve rocker arm cover bolts.
  24. Remove the upper valve rocker arm cover.
  25. Remove the upper valve rocker arm cover gasket.
  26. Inspect the upper valve rocker arm cover gasket for damage, replace if necessary. Otherwise reuse the old gasket.
  27. If required, clean and inspect the upper valve rocker arm cover. Refer to Valve Rocker Arm Cover Cleaning and Inspection - Upper .

Installation Procedure


    Object Number: 1335653  Size: SH
  1. Install the upper valve rocker arm cover gasket.
  2. Install the upper valve rocker arm cover.
  3. Install the upper valve rocker arm cover bolts.
  4. Notice: Refer to Fastener Notice in the Preface section.


    Object Number: 1411030  Size: SH
  5. Tighten the upper valve rocker arm cover bolts in the sequence shown.
  6. Tighten
    Tighten the bolts to 8 N·m (71 lb in).


    Object Number: 1335614  Size: SH

    Notice: Ensure proper torquing of the fuel injector line. An under-torqued fuel injector line will not seal properly and an over-torqued fuel injector line may damage the fuel injector fitting. An improperly sealed or damaged fuel injector line or fuel injector fitting will cause a fuel leak.

  7. Install the fuel injector pipes.
  8. Tighten
    Tighten the pipes to 41 N·m (30 lb ft).


    Object Number: 1602054  Size: SH
  9. Install the PCV hose/pipe. Refer to Positive Crankcase Ventilation Hose/Pipe/Tube Replacement .
  10. Position the fuel filter with bracket to the rocker cover.
  11. Install the fuel filter bracket bolts.
  12. Tighten
    Tighten the bolts to 21 N·m (15 lb ft).

  13. Position the heater outlet hose.
  14. Install the heater hose bracket bolt to the bracket.
  15. Tighten
    Tighten the bolt to 21 N·m (15 lb ft).

  16. Install the EGR cooler tube. Refer to Exhaust Gas Recirculation Valve Cooler Replacement .

  17. Object Number: 1601448  Size: SH
  18. Install the bracket.
  19. Install the oil level indicator tube bracket bolts.
  20. Tighten
    Tighten the bolts to 21 N·m (15 lb ft).

  21. Install the oil level indicator tube bolt.
  22. Tighten
    Tighten the bolt to 21 N·m (15 lb ft).

  23. Install the wiring harness retainer to the bracket.

  24. Object Number: 1653035  Size: SH
  25. Install a NEW quick connect fitting clip to the charged air cooler duct.
  26. Install the charged air cooler outlet duct to the intake.
  27. Install the air cleaner outlet duct. Refer to Air Cleaner Outlet Duct Replacement .
  28. Install the intake manifold cover. Refer to Intake Manifold Cover Replacement .