GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 GMC_Truck 🢒 1999 🢒 GMC K Pickup - 4WD 🢒 Body and Accessories 🢒 Doors 🢒 Speaker Replacement

Speaker Replacement Front Side Door

Removal Procedure

    Object Number: 264164 Size: SH
  1. Remove the trim panel. Refer to Front Side Door Trim Panel Replacement in Doors.
  2. Remove the screws.
  3. Use a small screwdriver in order to release the speaker retainer.
  4. Remove the speaker.
  5. Disconnect the electrical connector.

Installation Procedure

    Object Number: 264164 Size: SH
  1. Connect the electrical connector.
  2. Install the speaker.

    3. Snap the speaker into the retainer when the speaker is fully seated.

    Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

  3. Install the screws

    4. Tighten
    Tighten the screws to 2 N·m (18 lb in).

  4. Install the trim panel.
  5. Inspect the component's operation.

Speaker Replacement Front Door Armrest

Removal Procedure

    Object Number: 264167 Size: SH
  1. Lift the armrest speaker cover at the rear edge in order to remove the armrest speaker.
  2. Slide the cover back from the armrest speaker in order to disconnect the front retainer.
  3. Disconnect the electrical connector.
  4. Rotate the speaker in order to remove the speaker.

Installation Procedure

    Object Number: 264167 Size: SH
  1. Connect the speaker to the cover by rotating the speaker.

    2. The speaker should snap into the retainer when it is fully seated.

  2. Connect the electrical connector.
  3. Slide the speaker cover into the front slots.
  4. Lower the armrest speaker cover in order to connect the retainers.

Speaker Replacement Rear

Removal Procedure

    Object Number: 264171 Size: SH
  1. Remove the speaker grille.

    2. Object Number: 264169 Size: SH
  2. Remove the screws.
  3. Remove the speaker.

    4. Object Number: 264173 Size: SH
  4. Disconnect the electrical connectors.

Installation Procedure

    Object Number: 264173 Size: SH
  1. Connect the electrical connectors.

    2. Object Number: 264169 Size: SH
  2. Install the speaker.

    3. Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

  3. Install the screws.

    4. Tighten
    Tighten the screws to 2 N·m (18 lb in).


    Object Number: 264171 Size: SH
  4. Install the speaker grille.

    5. Verify the component's operation.

Speaker Replacement Side Door

Removal Procedure

    Object Number: 264181 Size: SH
  1. Remove the speaker grille.
  2. Remove the retainers.
  3. Remove the speaker.
  4. Disconnect the electrical connectors.

Installation Procedure

    Object Number: 264181 Size: SH
  1. Install the electrical connectors.
  2. Install the speaker.
  3. Install the retainers.
  4. Install the speaker grille.
  5. Verify the component's operation.

Speaker Replacement Rear Overhead

Removal Procedure

    Object Number: 264184 Size: MH
  1. Remove the speaker grille.
  2. Remove the roof inner trim panel, if necessary. Refer to Headlining Trim Panel Replacement in Interior Trim.
  3. Remove the screws.
  4. Remove the speaker from the bracket.
  5. Disconnect the electrical connectors, as necessary.

Installation Procedure

    Object Number: 264184 Size: MH
  1. Connect the electrical connectors, as necessary.
  2. Install the speaker to the bracket.

    3. Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

  3. Install the screws.

    4. Tighten
    Tighten the screws to 2 N·m (18 lb in).

  4. Install the roof inner trim panel, if necessary.
  5. Install the speaker grille.
  6. Verify the component's operation.