GM Service Manual Online
For 1990-2009 cars only

Circuit Description

The body control module (BCM) monitors the front fog lamp switch signal circuit in order to determine when the fog lamp relay is to be energized. When the BCM senses that the front fog lamp switch signal circuit is low momentarily by pressing the fog lamp switch, the BCM energizes the fog lamp relay by grounding the fog lamp relay control circuit.

Conditions for Running the DTC

    • The battery voltage must be between 9.0-16.0 volts.
    • Ignition switch in the RUN position.
    • Fog lamp switch ON.

Conditions for Setting the DTC

When the front fog lamp switch signal circuit is shorted to ground for approximately 3 minutes.

Action Taken When the DTC Sets

The fog lamps will not operate.

Conditions for Clearing the MIL/DTC

    • This DTC will clear on current status after the condition for setting the fault is corrected.
    • A history DTC will clear after 100 consecutive ignition cycles without a fault present.
    • History and current DTC(s) can be cleared using a scan tool.

Diagnostic Aids

    • Test the fog lamp switch for sticking in the ON position.
    • Perform a visual inspection for loose or poor connections at all related components. Refer to Testing for Intermittent Conditions and Poor Connections in Wiring Systems.

Test Description

The numbers below refer to the step numbers on the diagnostic table.

  1. OFF is the normal state of the switch before activation.

  2. OFF is the normal state of the switch before activation.

  3. This step tests for a short to ground on the signal circuit.

  4. After replacement of the BCM you must calibrate the new module for proper operation.

Step

Action

Value(s)

Yes

No

Schematic Reference: Fog Lights Schematics

Connector End View Reference: Lighting Systems Connector End Views or Body Control System Connector End Views in Body Control System

1

Did you perform the Lighting System Diagnostic System Check?

--

Go to Step 2

Go to Diagnostic System Check - Lighting Systems

2

  1. Install a scan tool.
  2. Turn ON the ignition, with the engine OFF.
  3. With a scan tool, observe the front fog lamp switch parameter in the Body Control Module (BCM) data list.

Does the scan tool display OFF?

OFF/ON

Go to Step 3

Go to Step 4

3

  1. Activate the front fog lamp switch.
  2. With the scan tool, observe the front fog lamp switch parameter.

Does the front fog lamp switch parameter change state?

--

Go to Diagnostic Aids

Go to Step 4

4

  1. Turn OFF the ignition.
  2. Disconnect the front fog lamp switch.
  3. Turn ON the ignition, with the engine OFF.
  4. With a scan tool, observe the front fog lamp switch parameter.

Does the scan tool display OFF?

OFF/ON

Go to Step 7

Go to Step 5

5

Test the signal circuit of the front fog lamp switch for a short to ground. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 10

Go to Step 6

6

Inspect for poor connections at the harness connector of the body control module. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 10

Go to Step 8

7

Inspect for poor connections at the harness connector of the front fog lamp switch. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 10

Go to Step 9

8

Important: Perform the set up procedure for the BCM.

Replace the body control module (BCM). Refer to Body Control Module Replacement in Body Control System.

Did you complete the replacement?

--

Go to Step 10

--

9

Replace the front fog lamp switch. Refer to Headlamp Switch Replacement .

Did you complete the replacement?

--

Go to Step 10

--

10

  1. Use the scan tool in order to clear the DTCs.
  2. Operate the vehicle within the Conditions for Running the DTC as specified in the supporting text.

Does the DTC reset?

--

Go to Step 2

System OK