GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 GMC_Truck 🢒 1999 🢒 Savana 🢒 Brakes 🢒 Hydraulic Brakes 🢒 Brake Shoe Replacement

GM replacement rear brake shoe material is recommended for all vehicles to maintain the balance between front and rear brake performance. GM replacement brake parts have been carefully selected to provide the proper brake balance for the purposes of stopping distance and control over the full range of operating conditions. Installation of front or rear brake material with performance different from that of GM replacement parts recommended for this vehicle can change the intended brake balance of the vehicle.

Removal Procedure

Caution: Avoid taking the following actions when you service wheel brake parts:

   • Do not grind brake linings.
   • Do not sand brake linings.
   • Do not clean wheel brake parts with a dry brush or with compressed air.
Some models or aftermarket brake parts may contain asbestos fibers which can become airborne in dust. Breathing dust with asbestos fibers may cause serious bodily harm. Use a water-dampened cloth in order to remove any dust on brake parts. Equipment is available commercially in order to perform this washing function. These wet methods prevent fibers from becoming airborne.

  1. Raise the vehicle and support the vehicle with safety stands.
  2. Remove the tire and the wheel. Refer to Tire and Wheel Removal and Installation in Tires and Wheels.
  3. Install the pin into the park brake lever. Refer to Parking Brake Cable Adjuster Enabling in Parking Brake.
  4. Remove the rear brake drum. Refer to Brake Drum Replacement .

    5. Object Number: 156753 Size: SH
  5. Remove the rear brake shoe return springs (7 and 8).
  6. Remove the hold-down springs (9).
  7. Remove the hold-down pins (15).
  8. Remove the shoe guide (3).
  9. Remove the rear brake shoe actuator (11), and the spring (10).
  10. Remove the rear brake shoe actuator link (6).
  11. Remove the rear parking brake lever strut (4) and spring (2).
  12. Remove the rear brake shoe adjuster spring (13).
  13. Remove the rear brake shoe adjuster (12).
  14. Remove the rear brake shoes (1 and 14).
  15. Inspect all of the parts for discoloration due to heat or stress. Replace as needed.
  16. Check for signs of wear. Replace as needed.
  17. Inspect the rear brake cylinder for signs of leakage. If any is found, refer to Wheel Cylinder Overhaul .
  18. Inspect the rear brake drum for scoring and machining tolerance. Refer to Brake Drum Inspection .

Installation Procedure

    Object Number: 156753 Size: SH
  1. Lubricate the rear brake backing plate and the adjusting screw threads with a thin coat of white lithium grease.
  2. Install the rear brake shoes (1 and 14).
  3. Install the rear brake shoe adjuster (12).

    4. Important: Do not interchange the right and left brake shoe adjusting screws.

  4. Install the rear brake shoe adjuster spring (13). The coils of the adjusting screw spring must not touch the adjusting screw.
  5. Install the rear parking brake lever strut (4) and spring (2).
  6. Install the rear brake shoe actuator link (6).
  7. Instal the rear brake shoe actuator (11) and spring (10).
  8. Install the shoe guide (3).
  9. Install the hold-down pins (15).
  10. Install the hold-down springs (9).
  11. Install the rear brake shoe return springs (7 and 8).
  12. Install the rear brake drum to the vehicle. Refer to Brake Drum Replacement .
  13. Remove the pin to the park brake lever. Refer to Parking Brake Cable Adjuster Enabling in Parking Brake.
  14. Install the tire and the wheel. Refer to Tire and Wheel Removal and Installation in Tires and Wheels.
  15. Adjust the rear brakes. Refer to Drum Brake Adjustment .
  16. Adjust the parking brake. Refer to Park Brake Cable Service/Adjustment in Park Brake.
  17. Remove the safety stands. Lower the vehicle.