GM Service Manual Online
For 1990-2009 cars only

Cruise Control Does Not Resume, Accel, Tap Up or Down Gasoline Engine

Step

Action

Value(s)

Yes

No

1

Was the Cruise Control System Check performed?

--

Go to Step 2

Go to Cruise Control System Check

2

  1. Disconnect the connector at the cruise control module.
  2. Disconnect connector C200 at the steering column.
  3. Connect a J 39200 between the cruise control module connector cavity C and connector C200 pin A15 for CKT 87 (GRY/BLK).

Is continuity present?

--

Go to Step 4

Go to Step 3

3

Repair the open in CKT 87 (GRY/BLK) between connector C200 and the cruise control module.

Does the cruise still not resume, accelerate or tap up?

--

Go to Step 4

Go to Cruise Control System Check

4

  1. Place the cruise control switch in the ON position.
  2. Connect a J 39200 between connector C200 cavity A13 for the CKT 41 (BRN) pigtail wire and cavity A15 for the CKT 87 (GRY/BLK) pigtail wire.
  3. Actuate the RESUME/ACCEL position on the cruise control switch.

Is continuity present?

--

Go to Step 5

Go to Step 6

5

Replace the cruise control module. Refer to Cruise Control Module Replacement .

Does the cruise still not resume, accelerate or tap up?

--

--

Go to Cruise Control System Check

6

Inspect for an open in the CKT 87 (GRY/BLK) pigtail wire in the steering column.

Did you find an open?

--

Go to Step 7

Go to Step 8

7

Repair the open in the CKT 87 (GRY/BLK) pigtail wire in the steering column.

Does the cruise still not resume, accelerate or tap up?

--

--

Go to Cruise Control System Check

8

Replace the multifunction lever with includes the cruise control switch. Refer to Cruise Control Switch Replacement .

Does the cruise still not resume, accelerate or tap up?

--

--

Go to Cruise Control System Check

Cruise Control Does Not Resume, Accel, Tap Up or Down Diesel Engine

Step

Action

Value(s)

Yes

No

1

Was the Cruise Control System Check performed??

--

Go to Step 2

Go to Cruise Control System Check

2

  1. Disconnect connector C200 at the steering column.
  2. Connect a J 39200 between connector C200 cavity A13 for the CKT 41 (BRN) pigtail wire and cavity A15 for the CKT 87 (GRY/BLK) pigtail wire.
  3. Slide the cruise control slider switch to the RESUME/ACCEL position.

Is continuity present?

--

Go to Step 6

Go to Step 3

3

Inspect for an open in the CKT 87 (GRY/BLK) pigtail wire in the steering column.

Did you find an open?

--

Go to Step 4

Go to Step 5

4

Repair the open in the CKT 87 (GRY/BLK) pigtail wire in the steering column.

Does the cruise still not resume, accelerate or tap up?

--

Go to Step 6

Go to Cruise Control System Check

5

Replace the multifunction lever with includes the cruise control switch. Refer to Cruise Control Switch Replacement .

Does the cruise still not resume, accelerate or tap up?

--

Go to Step 6

Go to Cruise Control System Check

6

  1. Disconnect connector C1 at the powertrain control module (PCM).
  2. Connect a J 39200 between the PCM connector C1 cavity D10 and connector C200 pin A15 for CKT 87 (GRY/BLK).

Is continuity present?

--

Go to Step 7

Go to Step 8

7

Replace the PCM. Refer to PCM Replacement in Engine Controls.

Does the cruise still not resume, accelerate or tap up?

--

--

Go to Cruise Control System Check

8

Repair the open in CKT 87 (GRY/BLK) between connector C200 and the PCM.

Does the cruise still not resume, accelerate or tap up?

--

--

Go to Cruise Control System Check