Circuit Description
The fuel level sensor changes resistance in response to fuel level. The powertrain control module (PCM) monitors the signal circuit of the fuel level sensor in order to determine the fuel level. When the fuel tank is full, the sensor resistance is low and the PCM senses a low signal voltage. When the fuel tank is empty, the sensor resistance is high and the PCM senses a high signal voltage. The PCM uses the signal circuit of the fuel level sensor in order to calculate the percentage of remaining fuel in the tank. The PCM sends the fuel level percentage via the class 2 serial data circuit to the instrument cluster in order to control the fuel gage. The fuel level information is also used for misfire and evaporative emission (EVAP) diagnostics.
DTC Descriptor
This diagnostic procedure supports the following DTC:
DTC P0462 Fuel Level Sensor 1 Circuit Low Voltage
Conditions for Running the DTC
The engine is running.
Conditions for Setting the DTC
| • | The sender output is less than 0.39 volts. |
| • | The above condition is present for greater than 30 seconds. |
Action Taken When the DTC Sets
| • | The fuel gage defaults to empty. |
| • | The low fuel indicator illuminates. |
| • | The PCM records the operating conditions at the time that the diagnostic test fails. The PCM displays the failure information in the Failure Records on the scan tool. |
Conditions for Clearing the DTC
| • | The DTC becomes history when the conditions for setting the DTC are no longer present. |
| • | The history DTC clears after 40 malfunction-free warm-up cycles. |
| • | The PCM receives the clear code command from the scan tool. |
Diagnostic Aids
Use the Freeze Frame/Failure Records data in order to locate an intermittent condition. If you cannot duplicate the DTC, the information included in the Freeze Frame/Failure Records data may help in determining the number of miles since the DTC set. The Fail Counter and Pass Counter can also help in determining the number of ignition cycles that the diagnostic test reported a pass and/or fail. Operate the vehicle within the same freeze frame conditions, including those for RPM, for engine load, for vehicle speed, for temperature, and for others. This will isolate at what point the DTC failed.
Refer to Testing for Intermittent Conditions and Poor Connections .
Test Description
The number below refers to the step number on the diagnostic table.
Step | Action | Values | Yes | No | ||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
Schematic Reference: Instrument Cluster Schematics Connector End View Reference: Master Electrical Component List | ||||||||||||
1 | Did you perform the Diagnostic System Check - Vehicle? | -- | Go to Step 2 | |||||||||
2 |
Does the scan tool indicate that the Fuel Tank Level Remaining parameter is greater than the specified value or the Fuel Level Sensor parameter is less than the specified value? | 98% 0.5 V - 6.6L diesel only | Go to Step 3 | Go to Diagnostic Aids | ||||||||
Does the scan tool indicate that the Fuel Tank Level Remaining parameter is less than the specified value or the Fuel Level Sensor parameter is greater than the specified value? | 4% 4.5 V - 6.6L diesel only | Go to Step 5 | Go to Step 4 | |||||||||
4 | Test the signal circuit of the fuel level sensor for a short to ground. Refer to Circuit Testing and Wiring Repairs . Did you find and correct the condition? | -- | Go to Step 10 | Go to Step 7 | ||||||||
5 | Test the signal circuit of the fuel level sensor for a short to ground between C152 and the fuel level sensor. Refer to Circuit Testing and Wiring Repairs . Did you find and correct the condition? | -- | Go to Step 10 | Go to Step 6 | ||||||||
6 | Inspect for poor connections at the harness connector of the fuel level sensor. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs . Did you find and correct the condition? | -- | Go to Step 10 | Go to Step 8 | ||||||||
7 | Inspect for poor connections at the harness connector of the PCM. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs . Did you find and correct the condition? | -- | Go to Step 10 | Go to Step 9 | ||||||||
8 | Replace the fuel level sensor. Refer to the following procedures:
Did you complete the replacement? | -- | Go to Step 10 | -- | ||||||||
9 | Replace the PCM. Refer to Control Module References for replacement, setup, and programming. Did you complete the replacement? | -- | Go to Step 10 | -- | ||||||||
10 |
Does the DTC reset? | -- | Go to Step 2 | System OK | ||||||||
