Sunroof Sunshade Replacement Extended Cab

Important: If the sunshade spring releases, it will be necessary to rewind it. Turn the sunshade roller end slot  20 times in the counterclockwise direction.

Important: A new sunshade service part comes pre-loaded with a pin tool holding spring tension on the sunshade. If the sunshade spring releases, it will be necessary to rewind it and reinstall the pin tool. Following installation, retain the pin tool for future applications.

1. Remove the sunroof window. Refer to Sunroof Window Replacement .
2. Power the sunroof window guides to the fully open position.




Important: The cam locking hole will come in to view when the sunshade is in the fully open position on the passengers side.

3. Close the sunshade (1) until the cam locking hole (2) come in to view.



4. Insert a suitable tool (1) into the sunshade cam locking hole (2).



5. Turn the sunshade (1) counterclockwise until the shade cam (2) is align with the bracket (3) notch.



6. Lift upward on the sunshade (1) removing it from the bracket (2).




Important: The sunshade must be removed from the top of the vehicle.

7. Push the sunshade (1) inward to the driver side releasing it from the bracket (2) notch.
8. Remove the sunshade from outside of the vehicle.

1. Install the sunshade to the vehicle from the passengers side.



2. Insert the end of the sunshade (1) to the driver side bracket (2) notch.



3. Insert the sunshade (1) to the passengers side bracket (2) notch.



4. Turn the sunshade cam (2) until it is aligned with the bracket (3) notch.
5. Install the sunshade.



6. Remove the suitable tool (1) from the sunshade cam locking hole (2).
7. Ensure that the sunshade cam (2) is fully seated in the bracket (3) and the sunshade slides smoothly.
8. Install the sunroof window. Refer to Sunroof Window Replacement .
9. Verify the operation of the sunshade.

Sunroof Sunshade Replacement Crew Cab

1. Remove the sunroof window. Refer to Sunroof Window Replacement.



2. Remove the screws (1) that retain the water trough to the sunroof frame
3. Remove the water trough through the roof opening of the vehicle.
4. It is only necessary to lower the headliner. Only do those steps in the headliner replacement procedure that will lower the headline enough to gain access to the part to be remove. Refer to Headlining Trim Panel Replacement.



5. Remove the left and right sunroof housing drain gutters (1) from the rear of the sunroof frame (2). Refer to Sunroof Housing Drain Gutter Replacement
6. Slide the sunshade (3) rearward to release it from the tracks.
7. Remove the sunshade from the of the vehicle.

1. Position the front of the sunshade (3) to the rear of the sunroof frame (2).
2. Install the retaining tabs of the sunshade into the left and right sides of the track slots in the sunroof frame.
3. Slide the sunshade forward while simultaneously inserting the rear retaining tabs into the track slot
4. Ensure that the sunshade tabs are fully seated in the track slots, and the sunshade slides smoothly.
5. Install the left and right sunroof housing drain gutters (1) to the rear of the sunroof frame (2). Refer to Sunroof Housing Drain Gutter Replacement
6. Install the headliner. Refer to Headlining Trim Panel Replacement.
7. Install the water trough to the sunroof from the top of the vehicle.

Caution: Refer to Fastener Caution in the Preface section.




8. Install the screws (1) that retain the water trough to the sunroof frame.

Tighten
Tighten the screws to 1 N·m (9 lb in).

9. Install the sunroof window. Refer to Sunroof Window Replacement.