Rear Seat Cushion Cover and Pad Replacement 60/40 Split - 50/50 Split
Removal Procedure
- Remove the rear passenger seat from the vehicle. Refer to
Rear Seat Replacement
,
Rear Number 2 Seat Replacement
or
Rear Number 2 50-50 Seat Replacement
.
- Remove the rear passenger seat riser.
- Remove the seat cushion plastic cover from the seat cushion frame.
- Remove the hog rings and/or the J-clips from the rear edge of the seat
cushion cover (3).
- Disconnect the rear heater connector, if equipped.
- Remove the seat belt buckles, if required. Refer to
Rear Seat Belt Buckle Replacement
or
Rear Seat Number 2 Belt Buckle Replacement
in Seat Belts.
- Remove all of the remaining hog rings, and/or the J-clips that are retaining
the seat cushion cover (3) to the seat cushion frame (8).
- Release the hook, and the loop-strips that are retaining the seat cushion
cover to the foam pad (4).
- Remove the center screw retaining the latch cover.
- Remove the seat cushion cover from the foam pad.
Installation Procedure
- Install the seat cushion cover to the foam
pad.
Notice: Use the correct fastener in the correct location. Replacement fasteners
must be the correct part number for that application. Fasteners requiring
replacement or fasteners requiring the use of thread locking compound or sealant
are identified in the service procedure. Do not use paints, lubricants, or
corrosion inhibitors on fasteners or fastener joint surfaces unless specified.
These coatings affect fastener torque and joint clamping force and may damage
the fastener. Use the correct tightening sequence and specifications when
installing fasteners in order to avoid damage to parts and systems.
- Install the center screw retaining the latch cover.
Tighten
Tighten the screw to 2 N·m (18 lb in).
- Engage the hook, and the loop-strips that are retaining the seat cushion
cover (3) to the foam pad (4).
- Install the seat buckles, if removed. Refer to
Rear Seat Belt Buckle Replacement
or
Rear Seat Number 2 Belt Buckle Replacement
in Seat Belts.
- Connect the rear heater connector, if equipped.
- Install the hog rings, and/or the J-clips in order to retain the seat
cushion cover to the seat cushion frame (8).
- Install the seat cushion plastic cover to the seat cushion frame.
- Install the rear passenger seat risers.
- Install the rear passenger seat to the vehicle. Refer to
Rear Seat Replacement
,
Rear Number 2 Seat Replacement
or
Rear Number 2 50-50 Seat Replacement
.
Rear Seat Cushion Cover and Pad Replacement Bench
Removal Procedure
- Remove the rear seat from the vehicle. Refer
to
Rear Number 2 Seat Replacement
.
- Remove the J-Clips from the back of the seat.
- Remove the bolts (2) from the grab handle (1).
- Remove the support rod (1) from the bottom
of the seat.
- Loosen the bolts (1) on the roller assembly
(2) but do not remove.
- Remove the seat cushion cover and pad from the seat frame.
Installation Procedure
Notice: Refer to Fastener Notice in the Preface section.
- Install the seat cushion cover and pad to
the seat frame.
- Install the bolts (1) on the roller assembly (2).
Tighten
Tighten the bolts to 53 N·m (39 lb ft).
- Install the support rod (1) to the bottom
of the seat.
- Install the bolts (2) to the grab handle
(1).
Tighten
Tighten the bolts to 30 N·m (22 lb ft).
- Install the J-Clips on the back of the seat.
- Install the rear seat to the vehicle. Refer to
Rear Number 2 Seat Replacement
.