GM Service Manual Online
For 1990-2009 cars only

Linear Shift Assembly - Assemble - Off Vehicle Column Shift


    Object Number: 662202  Size: SH
  1. Install the linear shift assembly onto the steering column support assembly.
  2. Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

  3. Secure the linear shift assembly to the steering column assembly with the 3 flat head tapping screws.
  4. Move the linear shift assembly out of the PARK position to install the lower socket tapping screw.

    Tighten
    Tighten the 3 TORX® screws to 10 N·m (89 lb in).


    Object Number: 324906  Size: SH
  5. Install the automatic transmission shift lock control.
  6. Install the shift lever clevis and put the column in the neutral position.
  7. The neutral position is 2 positions from the park position.

  8. Object Number: 662195  Size: SH
  9. Slide the park position switch assembly onto the linear shift assembly.
  10. Connect the automatic transmission shift lock control connector onto the park position switch assembly.

  11. Object Number: 324874  Size: SH
  12. Connect the park lock cable assembly (1) to the lock module assembly in the following way:
  13. 8.1. Place the steering column lock cylinder set into the off position.
    8.2. Place the shift lever clevis into the park position.
    8.3. Press the locking tab on the end of the park lock cable assembly (1) into the slot in the lock module assembly.
  14. Install the shift lever. Refer to Shift Lever Replacement - On Vehicle .
  15. Install the upper and lower trim covers. Refer to Steering Column Trim Covers - Assemble - Off Vehicle .
  16. Enable the inflatable restraint steering wheel module. Refer to Enabling the SIR System in SIR.

Linear Shift Assembly - Assemble - Off Vehicle Export


    Object Number: 662202  Size: SH
  1. If you need to assemble the linear shift assembly first proceed to step 3.
  2. Install the linear shift assembly onto the steering column support assembly.

    Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

  3. Secure the linear shift assembly to the steering column assembly with the 3 flat head tapping screws.
  4. Move the linear shift assembly out of the PARK position to install the lower socket tapping screw.

    Tighten
    Tighten the 3 TORX® screws to 10 N·m (89 lb in).


    Object Number: 662190  Size: SH
  5. Install the shift lever gate (3) onto the gear shift lever assembly support bracket (1).
  6. Install the 3 oval head screws (2) onto the shift lever gate (3).
  7. Tighten
    Tighten the 3 oval head screws to 7 N·m (62 lb in).


    Object Number: 662186  Size: SH
  8. Install the 2 actuator bushings.

  9. Object Number: 662176  Size: SH
  10. Install the shift actuator shaft.

  11. Object Number: 662173  Size: SH
  12. Install the cable shift cam assembly (3).
  13. Install the ball and actuator assembly (1).
  14. Install the 2 hexagon flange head bolts (2).
  15. Tighten
    Tighten the 2 hexagon flange head bolts to 18 N·m (13 lb ft).


    Object Number: 324906  Size: SH
  16. Install the automatic transmission shift lock control.
  17. Install the shift lever clevis and put the column in the neutral position.

    This will be 2 positions from the park position.


    Object Number: 662195  Size: SH
  18. Snap the park position switch assembly onto the linear shift assembly.
  19. Connect the automatic transmission shift lock control connector onto the park position switch assembly.

  20. Object Number: 324874  Size: SH
  21. Connect the park lock cable assembly (1) to the lock module assembly in the following way:
  22. • Place the steering column lock cylinder set into the off position.
    • Place the shift lever clevis into the park position.
    • Press the locking tab on the end of the park lock cable assembly (1) into the slot in the lock module assembly.
  23. Install the upper and lower trim covers. Refer to Steering Column Trim Covers - Assemble - Off Vehicle .