Schematic Reference: Exterior Lights Schematics

Connector End View Reference: Lighting Systems Connector End Views or Computer/Integrating Systems Connector End Views in Computer/Integrating Systems

Did you perform the Diagnostic System Check - Vehicle?

Go to Step 2

Go to Diagnostic System Check - Vehicle in Vehicle DTC Information

Verify that the turn signal lamps and/or indicators are inoperative.

Do the turn signal lamps and/or indicators operate normally?

Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems

Go to Step 3

Are only the turn signal indicators in the instrument panel cluster (IPC) inoperative?

Go to Step 4

Go to Step 5

Test the inoperative turn signal supply voltage circuit to the IPC for an open or high resistance. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 21

Go to Step 13

Is only one turn signal lamp inoperative?

Go to Step 6

Go to Step 8

Inspect the inoperative bulb/socket for an internal short, poor terminal contact, or an open filament.

Was a problem found?

Go to Step 18

Go to Step 7

Test for an open, high resistance, or short to ground in the turn signal lamp supply voltage circuit. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 21

Go to Step 16

Inspect the IGN E fuse and the FLASHER fuse.

Is either fuse open?

Go to Step 11

Go to Step 9

Test for an open or high resistance in the following circuits:

Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 21

Go to Step 10

1. Disconnect the multifunction switch, turn signal switch.
2. Test the multifunction turn signal switch for continuity between the multifunction turn signal switch ignition 1 voltage input terminal and the turn signal flasher signal output terminal in each respective position. Refer to Circuit Testing in Wiring Systems.

Is continuity present?

Go to Step 12

Go to Step 14

Test the following circuits for a short to ground:

Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 21

Go to Step 14

Test the following circuits for an open or high resistance:

Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 21

Go to Step 15

Inspect for poor connections at the IPC. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 21

Go to Step 17

Inspect for poor connections at the multifunction turn signal switch. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 21

Go to Step 19

Inspect for poor connections at the turn signal/hazard flasher module. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 21

Go to Step 20

Repair the ground circuit of the inoperative lamp. Refer to Wiring Repairs in Wiring Systems.

Did you complete the repair?

Go to Step 21

--

Replace the IPC. Refer to Control Module References in Computer/Integrating Systems for replacement, setup, and programming.

Did you complete the repair?

Go to Step 21

--

Replace or repair the inoperative bulb/socket.

Did you complete the repair?

Go to Step 21

--

Replace the multifunction turn signal switch. Refer to Turn Signal Multifunction Switch Replacement in Steering Wheel and Column.

Did you complete the repair?

Go to Step 21

--

Replace the turn signal/hazard flasher module. Refer to Hazard and Turn Signal Flasher Replacement .

Did you complete the repair?

Go to Step 21

--

Operate the system in order to verify the repair.

Did you correct the condition?

System OK

Go to Step 3