GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Isuzu 🢒 2006 🢒 Ascender - 2WD 🢒 Body 🢒 Bumpers 🢒 Front Bumper Fascia Replacement

Front Bumper Fascia Replacement Rainier

Removal Procedure
  1. Remove the grille. Refer to Grille Replacement .

    2. Object Number: 740666 Size: SH
  2. Remove the 2 bolts that retain the top of the fascia to the headlamp housing panel.
  3. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle .

    4. Object Number: 740663 Size: SH
  4. Remove the push-pins (3) that retain the fascia to the fascia support rods (2).
  5. Remove the fog lamps from the fascia. Refer to Front Fog Lamp Replacement .
  6. Remove the cornering lamps from the fascia. Refer to Cornering Lamp Replacement .
  7. Remove the air deflector from the fascia. Refer to Front Bumper Fascia Air Deflector Replacement .
  8. Release the body side attachment tabs and pull the fascia straight forward in order to remove the fascia from the vehicle.

Installation Procedure

    Object Number: 740663 Size: SH
  1. Position the fascia to the vehicle, ensuring that the body side attachment tabs are fully seated.
  2. Install the push-pins (3) that retain the fascia to the fascia support rods (2).
  3. Install the air deflector to the fascia. Refer to Front Bumper Fascia Air Deflector Replacement .
  4. Install the cornering lamps. Refer to Cornering Lamp Replacement .
  5. Install the fog lamps. Refer to Front Fog Lamp Replacement .
  6. Lower the vehicle.

    7. Object Number: 740665 Size: SH
  7. Install the push-pin in the upper center of the fascia.

    8. Notice: Refer to Fastener Notice in the Preface section.

  8. Install the 2 bolts that retain the top of the fascia to the headlamp housing panel.

    9. Tighten
    Tighten the bolts to 10 N·m (89 lb in).

  9. Install the grille. Refer to Grille Replacement .

Front Bumper Fascia Replacement TrailBlazer

Removal Procedure
  1. Remove the grille. Refer to Grille Replacement .

    2. Object Number: 740665 Size: SH
  2. Remove the 2 bolts that retain the top of the fascia to the headlamp housing panel.
  3. Remove the push-pin that retains the top of the fascia to the headlamp housing panel.
  4. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle .

    5. Object Number: 740663 Size: SH
  5. Remove the push-pins (3) that retain the fascia to the fascia support rods (2).
  6. Remove the fog lamps from the fascia. Refer to Front Fog Lamp Replacement .
  7. Remove the air deflector. Refer to Front Bumper Fascia Air Deflector Replacement .

    8. Object Number: 740665 Size: SH
  8. Remove the 4 push-pins that retain the bottom of the fascia to the headlamp housing panel.
  9. Release the body side attachment tabs and pull the fascia straight forward from the wheelhouse opening in order to remove the fascia from the vehicle.

Installation Procedure

    Object Number: 740665 Size: SH
  1. Position the fascia to the vehicle, ensuring that the body side attachment tabs are fully seated.
  2. Install the 4 push-pins that retain the bottom of the fascia to the headlamp housing panel.

    3. Object Number: 740663 Size: SH
  3. Install the push-pins (3) that retain the fascia to the fascia support rods (2).
  4. Install the air defector. Refer to Front Bumper Fascia Air Deflector Replacement .
  5. Install the fog lamps. Refer to Front Fog Lamp Replacement .
  6. Lower the vehicle.

    7. Notice: Refer to Fastener Notice in the Preface section.


    Object Number: 740665 Size: SH
  7. Install the 2 bolts that retain the top of the fascia to the headlamp housing panel.

    8. Tighten
    Tighten the bolts to 10 N·m (89 lb in).

  8. Install the push-pin that retains the center of the top of the fascia to the headlamp housing panel.
  9. Install the grille. Refer to Grille Replacement .

Front Bumper Fascia Replacement Envoy

Removal Procedure
  1. Remove the grille. Refer to Grille Replacement .

    2. Object Number: 740665 Size: SH
  2. Remove the 2 bolts that retain the top of the fascia to the headlamp housing panel.
  3. Remove the push-pin that retains the top of the fascia to the headlamp housing panel.
  4. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle .

    5. Object Number: 740663 Size: SH
  5. Remove the push-pins (3) that retain the fascia to the fascia support rods (2).
  6. Remove the fog lamps from the fascia. Refer to Front Fog Lamp Replacement .
  7. Remove the cornering lamps from the fascia. Refer to Cornering Lamp Replacement .
  8. Remove the air deflector. Refer to Front Bumper Fascia Air Deflector Replacement .

    9. Object Number: 740665 Size: SH
  9. Remove the 4 push-pins that retain the bottom of the fascia to the headlamp housing panel.
  10. Release the body side attachment tabs and pull the fascia straight forward in order to remove the fascia from the vehicle.

Installation Procedure

    Object Number: 740665 Size: SH
  1. Position the fascia to the vehicle, ensuring that the body side attachment tabs are fully seated.
  2. Install the 4 push-pins that retain the bottom of the fascia to the headlamp housing panel.

    3. Object Number: 740663 Size: SH
  3. Install the push-pins (3) that retain the fascia to the fascia support rods (2).
  4. Install the air defector. Refer to Front Bumper Fascia Air Deflector Replacement .
  5. Install the cornering lamps. Refer to Cornering Lamp Replacement .
  6. Install the fog lamps. Refer to Front Fog Lamp Replacement .
  7. Lower the vehicle.

    8. Notice: Refer to Fastener Notice in the Preface section.


    Object Number: 740665 Size: SH
  8. Install the 2 bolts that retain the top of the fascia to the headlamp housing panel.

    9. Tighten
    Tighten the bolts to 10 N·m (89 lb in).

  9. Install the push-pin that retains the center of the top of the fascia to the headlamp housing panel.
  10. Install the grille. Refer to Grille Replacement .