DTC P0758 2-3 (B) Shift Solenoid Electrical 2.2L
| Table 1: | Shift Solenoid Valve State and Gear Ratio 4L60-E |
| Table 2: | DTC P0758 2-3 Shift Solenoid Valve -- Electrical |
Circuit Description
The 2-3 Shift Solenoid Valve (2-3 SS Valve) controls the fluid flow acting on the 2-3 shift valves. The 2-3 SS Valve is a normally-open exhaust valve that is used with the 1-2 Shift Solenoid Valve in order to allow four different shifting combinations. The solenoid attaches to the control valve body within the transmission. The 2-3 SS Valve receives ignition voltage through circuit 1020. The PCM controls the solenoid by providing the ground path on circuit 1223.
When the PCM detects a continuous open or short to ground in the 2-3 SS Valve circuit or the 2-3 SS Valve, then DTC P0758 sets. DTC P0758 is a type A DTC.
Conditions for Setting the DTC
| • | The system voltage is 10-17 volts. |
| • | The engine is running. |
| • | All of the above conditions are met for 5 seconds, and either of the following fail conditions occurs for 5 seconds. |
| - | The PCM commands the solenoid ON and the voltage remains high (B+). |
| - | The PCM commands the solenoid OFF and the voltage remains low (0 volts). |
Action Taken When the DTC Sets
| • | The PCM commands third gear only. |
| • | The PCM commands maximum line pressure. |
| • | The PCM freezes shift adapts from being updated. |
| • | The PCM inhibits TCC engagement. |
| • | The PCM illuminates the Malfunction Indicator Lamp (MIL). |
Conditions for Clearing the MIL/DTC
| • | The PCM turns OFF the MIL after three consecutive ignition cycles without a failure reported. |
| • | A scan tool can clear the DTC from the PCM history. The PCM clears the DTC from the PCM history if the vehicle completes 40 warm-up cycles without a failure reported. |
| • | The PCM cancels the DTC default actions when the fault no longer exists and the ignition is OFF long enough in order to power down the PCM. |
Diagnostic Aids
| • | Inspect the wiring for poor electrical connections at the PCM. Inspect the wiring for poor electrical connections at the transmission 20-way connector. Look for the following conditions: |
| • | A bent terminal |
| • | A backed out terminal |
| • | A damaged terminal |
| • | Poor terminal tension |
| • | A chafed wire |
| • | A broken wire inside the insulation |
| • | When diagnosing for an intermittent short or open condition, massage the wiring harness while watching the test equipment for a change. |
Gear | 1-2 Shift Solenoid | 2-3 Shift Solenoid | Gear Ratio |
|---|---|---|---|
1 | ON | ON | 3.059:1 |
2 | OFF | ON | 1.625:1 |
3 | OFF | OFF | 1.000:1 |
4 | ON | OFF | 0.696:1 |
Test Description
The numbers below refer to the step numbers on the diagnostic chart.
-
This step tests the function of the 2-3 SS Valve and the Automatic Transmission Wiring Harness Assembly.
-
This step tests for power to the 2-3 SS Valve from the ignition through the fuse.
-
This step measures the resistance of the component.
Step | Action | Value(s) | Yes | No | ||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
1 | Was the Powertrain On-Board Diagnostic (OBD) System Check performed? | -- | ||||||||||||||||
2 |
Important: Before clearing the DTCs, use the scan tool in order to record the Freeze Frame and Failure Records for reference. The Clear Info function will erase the data. Are DTCs P0753, P1860, P1864, and P1886 also set? | -- | ||||||||||||||||
3 |
Did you find and correct a problem? | -- | -- | |||||||||||||||
4 | Command the 2-3 SS Valve ON and OFF three times while listening to the bottom of the transmission pan (a stethoscope may be necessary). Does the solenoid click when commanded? | -- | Go to Diagnostic Aids | |||||||||||||||
5 |
Is the test light ON? | -- | ||||||||||||||||
6 |
Is the test lamp ON when the 2-3 SS Valve is commanded ON and OFF when commanded OFF? | -- | ||||||||||||||||
7 | Repair the open or short to ground in ignition feed circuit 1020 to the 2-3 SS Valve. Refer to Electrical diagnosis, Section 8. Did you find and correct a problem? | -- | -- | |||||||||||||||
8 | Monitor the test lamp status. Was the test lamp OFF at all times? | -- | ||||||||||||||||
9 |
Refer to Electrical diagnosis, Section 8. Did you find a problem? | -- | ||||||||||||||||
10 | Was the test lamp ON at all times? | -- | -- | |||||||||||||||
11 |
Refer to Electrical Diagnosis, Section 8. Did you find a problem? | -- | ||||||||||||||||
12 | Replace the PCM. Refer to Powertrain Control Module Replacement/Programming , Section 6. Is the replacement complete? | -- | -- | |||||||||||||||
13 |
Is the resistance within the specified range? | 19-31ohms | ||||||||||||||||
14 |
Is the resistance within the specified range? | 19-31ohms | ||||||||||||||||
15 | Using J 39200 DVOM, measure the resistance between terminals B and E and ground. Are both readings greater than the specified value? | 250kohms | Go to Diagnostic Aids | |||||||||||||||
16 |
Are both readings greater than the value shown? | 250kohms | ||||||||||||||||
17 | Replace the A/T Wiring Harness Assy. Refer to Automatic Transmission Wiring Harness Assembly Replacement, in On-Vehicle Service. Is the replacement complete? | -- | -- | |||||||||||||||
18 | Replace the 2-3 SS Valve. Refer to 2-3 Shift Solenoid Valve Replacement, in On-Vehicle Service. Is the replacement complete? | -- | -- | |||||||||||||||
19 | In order to verify your repair, perform the following procedure:
Has the test run and passed? | -- | System OK |
DTC P0758 2-3 (B) Shift Solenoid Electrical 4.3L
| Table 1: | Shift Solenoid Valve State and Gear Ratio 4L60-E |
| Table 2: | DTC P0758 2-3 Shift Solenoid Valve (2-3 SS Valve)-- Electrical |
Circuit Description
The 2-3 Shift Solenoid Valve (2-3 SS Valve) controls the fluid flow acting on the 2-3 shift valves. The solenoid is a normally-open exhaust valve. With the 1-2 Shift Solenoid Valve (1-2 SS Valve), the 2-3 SS Valve allows four different shifting combinations. The solenoid attaches to the control valve body within the transmission. The 2-3 SS Valve receives ignition voltage through circuit 1020. The VCM controls the solenoid by providing the ground path on circuit 1223.
When the VCM detects a continuous open or short to ground in the 2-3 SS Valve circuit or the 2-3 SS Valve, then DTC P0758 sets. DTC P0758 is a type A DTC.
Conditions for Setting the DTC
| • | The system voltage is 10-17 volts. |
| • | The engine is running. |
| • | All of the above conditions are met for 5 seconds and either of the following fail conditions occurs for 5 seconds: |
| - | The VCM commands the solenoid ON and the voltage remains high (B+). |
| - | The VCM commands the solenoid OFF and the voltage remains low (0 volts). |
Action Taken When the DTC Sets
| • | The VCM commands third gear only. |
| • | The VCM commands maximum line pressure. |
| • | The VCM freezes shift adapts from being updated. |
| • | The VCM inhibits TCC engagement. |
| • | The VCM illuminates the Malfunction Indicator Lamp (MIL). |
Conditions for Clearing the MIL/DTC
| • | The VCM turns OFF the MIL after three consecutive ignition cycles without a failure reported. |
| • | A scan tool can clear the DTC from the VCM history. The VCM clears the DTC from the VCM history if the vehicle completes 40 warm-up cycles without a failure reported. |
| • | The VCM cancels the DTC default actions when the fault no longer exists and the ignition is OFF long enough in order to power down the VCM. |
Diagnostic Aids
| • | Inspect the wiring for poor electrical connections at the VCM. Inspect the wiring for poor electrical connections at the transmission 20-way connector. Look for the following conditions: |
| • | A bent terminal |
| • | A backed out terminal |
| • | A damaged terminal |
| • | Poor terminal tension |
| • | A chafed wire |
| • | A broken wire inside the insulation |
| • | When diagnosing for an intermittent short or open condition, massage the wiring harness while watching the test equipment for a change. |
Gear | 1-2 Shift Solenoid | 2-3 Shift Solenoid | Gear Ratio |
|---|---|---|---|
1 | ON | ON | 3.059:1 |
2 | OFF | ON | 1.625:1 |
3 | OFF | OFF | 1.000:1 |
4 | ON | OFF | 0.696:1 |
Test Description
The numbers below refer to the step numbers on the diagnostic table.
-
This step tests the function of the 2-3 SS Valve and the Automatic Transmission Wiring Harness Assembly.
-
This step tests for power to the 2-3 SS Valve from the ignition through the fuse.
-
This step tests circuit 1223 from the transmission 20-way connector to the VCM for an open.
-
This step tests circuit 1223 from the transmission 20-way connector to the VCM for a short to ground.
Step | Action | Value(s) | Yes | No | ||||||
|---|---|---|---|---|---|---|---|---|---|---|
1 | Was the Powertrain On-Board Diagnostic (OBD) System Check performed? | -- | ||||||||
2 |
Important: Before clearing the DTCs, use the scan tool in order to record the Freeze Frame and Failure Records for reference. The Clear Info function will erase the data. Were DTCs P0753, P1860, P1864, and P1886 also set? | -- | ||||||||
3 |
Refer to Electrical Diagnosis, Section 8.
Did you find and correct a problem? | -- | -- | |||||||
Command the 2-3 SS Valve ON and OFF three times while listening to the bottom of the transmission pan (a stethoscope may be necessary). Does the solenoid click when commanded? | -- | Go to Diagnostic Aids | ||||||||
Is the test lamp ON? | -- | |||||||||
6 | Repair the open or short to ground in ignition feed circuit 1020 to the 2-3 SS Valve. Refer to Electrical Diagnosis, Section 8. Did you find and correct a problem? | -- | -- | |||||||
Is the resistance measured greater than the specified value? | 5ohms | |||||||||
Measure the resistance between C2-4 and a known good ground. Is the resistance measured less than the specified value? | 1000ohms | |||||||||
9 | Inspect circuit 1223 for an open. Repair the circuit if necessary. Did you find a problem? | -- | ||||||||
10 |
Refer to Electrical Diagnosis, Section 8. Did you find a problem? | -- | ||||||||
11 | Replace the VCM. Refer to VCM Replacement/Programming , Section 6. Is the replacement complete? | -- | -- | |||||||
12 |
Is the resistance within the specified range? | 19-31ohms | ||||||||
13 |
Is the resistance within the specified range? | 19-31ohms | ||||||||
14 | Measure the resistance between terminal B and terminal E and ground. Are both readings greater than the specified value? | 250kohms | Go to Diagnostic Aids | |||||||
15 |
Are both readings greater than the specified value? | 250kohms | ||||||||
16 | Replace the A/T Wiring Harness Assy. Refer to Automatic Transmission Wiring Harness Assembly Replacement, in On-Vehicle Service. Is the replacement complete? | -- | -- | |||||||
17 | Replace the 2-3 SS Valve. Refer to 2-3 Shift Solenoid Valve Replacement, in On-Vehicle Service. Is the replacement complete? | -- | -- | |||||||
18 | In order to verify your repair, perform the following procedure:
Has the test run and passed? | -- | System OK |
