Circuit Description
DTC C1248 detects a stripped nut or gear assembly during initialization. During the homing sequence, the piston should reach the top of the bore. Then the ABS motor stalls. If the ABS motor does not stall, the ABS motor must be spinning with little or no resistance. This indicates a nut/screw or gear malfunction.
Conditions for Setting the DTC
DTC C1248 can only set during initialization.
A malfunction exists if the feedback current is less than the command current for a specified period of time.
Action Taken When the DTC Sets
| • | A malfunction DTC stores. |
| • | The ABS/ETS disables. |
| • | The amber ABS/ETS warning indicators turn on. |
Conditions for Clearing the DTC
| • | The condition responsible for setting the DTC no longer exists and the Scan Tool Clear DTCs function is used. |
| • | 100 drive cycles pass with no DTCs detected. |
Diagnostic Aids
The following conditions may cause an intermittent malfunction if present in the mechanical portion of the system:
| • | Sticking |
| • | Binding |
| • | Slipping |
DTC C1248 may set after modulator disassembly if the modulator pistons are positioned at the bottom of the modulator piston bore. If DTC C1248 only occurs once and DTC C1261 also occurs, refer to DTC C1261 Right Front ABS Motor Circuit Open . If intermittent and enhanced diagnosis shows this DTC occurs during ABS operation, also refer to DTC C1261 Right Front ABS Motor Circuit Open .
Depending on the frequency of the malfunction, a physical inspection of the suspected mechanical parts causing the malfunction may be necessary.
Clear the DTCs after completing the diagnosis. Test drive the vehicle for three drive cycles in order to verify that the DTC does not reset. Use the following procedure in order to complete one drive cycle:
- Start the vehicle.
- Drive the vehicle over 16 km/h (10 mph).
- Stop the vehicle.
- Turn the ignition to the OFF position.
Step | Action | Value(s) | Yes | No | ||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
1 | Was the Diagnostic System Check performed? | -- | ||||||||||
2 |
Do not start the engine. Does DTC C1261 also set as a current DTC? | -- | ||||||||||
3 |
Observe the following currents:
Were the right front ABS motor command current and the right front ABS motor feedback current approximately the specified current? | 10 A | ||||||||||
4 |
Observe the following currents:
Have the following conditions been met?
| 6 A | ||||||||||
5 |
Did the brake pedal rise? | -- | ||||||||||
6 |
Is the resistance less than or equal to the specified value? | 1.5 ohms | ||||||||||
7 | Use the J 39200 in order to measure the resistance between the 6-way ABS brake motor pack connector terminal A and the 8-way EBTCM connector C2 terminal B. Is the resistance less than or equal to the specified value? | 1.5 ohms | ||||||||||
8 | Use the J 39200 in order to measure the resistance between the 6-way ABS brake motor pack connector terminal A and the 6-way ABS brake motor pack connector terminal B. Is the resistance less than or equal to the specified value? | 1.5 ohms | ||||||||||
9 |
(The ABS brake motor pack is the unit with the three small gears. The ABS brake motor pack right front gear is the gear closest to the rear when the ABS brake modulator is mounted in the vehicle.) Is the ABS brake motor right front gear stripped? | -- | ||||||||||
10 | Inspect for a stripped ABS brake modulator right front gear. (The ABS brake modulator unit is the unit with the three large gears. The ABS brake modulator right front gear is the gear closest to the rear when the ABS brake modulator is mounted in the vehicle.) Is the ABS brake modulator right front gear stripped? | -- | ||||||||||
11 |
Secure the assembly in a position that permits observation of the gears. Do not start the engine. (The ABS brake modulator right front gear is the gear closest to the rear when the ABS brake modulator is mounted in the vehicle.) Does the ABS brake modulator right front gear set move at least one full revolution in both directions? | -- | ||||||||||
12 |
Does the ABS brake modulator right front gear rotate more than 13 full turns from lock to lock? | -- | ||||||||||
13 |
Do any of the terminals exhibit poor terminal contact or corrosion? | -- | ||||||||||
14 |
Does DTC C1248 set as a current DTC? | -- | ||||||||||
15 | Repair the high resistance in CKT 1282. Is the repair complete? | -- | -- | |||||||||
16 | Repair the high resistance in CKT 1283. Is the repair complete? | -- | -- | |||||||||
17 | Replace the ABS brake motor pack. Refer to ABS Motor Pack Replacement . Is the repair complete? | -- | -- | |||||||||
18 | Replace the ABS brake modulator gear. Refer to Brake Modulator Gear Replacement . Is the repair complete? | -- | -- | |||||||||
19 | Replace the ABS brake modulator. Refer to Brake Modulator Replacement . Is the repair complete? | -- | -- | |||||||||
20 | Replace the terminals that exhibit signs of poor terminal contact or corrosion. Is the repair complete? | -- | -- | |||||||||
21 | Replace the EBTCM. Refer to Electronic Brake and Traction Control Module Replacement . Is the repair complete? | -- | -- | |||||||||
22 | Is the malfunction intermittent or is not present at this time? | -- | Go to Diagnostic Aids | -- |
