Circuit Description
The powertrain control module (PCM) supplies a voltage of about 450 mV between the HO2S high and low signal circuits. The oxygen sensor varies the voltage over a range from about 1,000 mV when the exhaust is rich, down through about 10 mV when the exhaust is lean.
The PCM monitors and stores the heated oxygen sensor (HO2S) voltage information. The PCM evaluates the HO2S voltage samples in order to determine the amount of time the HO2S voltage was out of range. The PCM compares the stored HO2S voltage samples taken within each sample period and determines if the majority of the samples are out of the operating range.
The PCM monitors the HO2S voltage and detects if the voltage goes out of the bias range. If the PCM does not detect the voltage went out of the bias range, a DTC sets.
Conditions for Running the DTC
| • | DTCs P0101, P0102, P0103, P0106, P0107, P0108, P0112, P0113, P0116, P0117, P0118, P0121, P0122, P0123, P0125, P0128, P0135, P0141, P0155, P0161, P0200, P0300, P0410, P0440, P0442, P0446, P0452, P0453, P1258, P1415, P1416, or P1441 are not set. |
| • | The engine run time is more than 409 seconds. |
| • | The ignition 1 signal is between 9-18 volts. |
| • | The loop status is closed. |
| • | The intrusive tests are not in progress. |
| • | The scan tool output controls are not active. |
Conditions for Setting the DTC
| • | The HO2S signal voltage is steady between 410-490 mV for 150 seconds. |
| • | The throttle position (TP) changes more than 5 percent within 1 second, 6 times. |
Action Taken When the DTC Sets
| • | The control module illuminates the malfunction indicator lamp (MIL) on the second consecutive ignition cycle that the diagnostic runs and fails. |
| • | The control module records the operating conditions at the time the diagnostic fails. The first time the diagnostic fails, the control module stores this information in the Failure Records. If the diagnostic reports a failure on the second consecutive ignition cycle, the control module records the operating conditions at the time of the failure. The control module writes the operating conditions to the Freeze Frame and updates the Failure Records. |
Conditions for Clearing the MIL/DTC
| • | The control module turns OFF the malfunction indicator lamp (MIL) after 3 consecutive ignition cycles that the diagnostic runs and does not fail. |
| • | A current DTC, Last Test Failed, clears when the diagnostic runs and passes. |
| • | A history DTC clears after 40 consecutive warm-up cycles, if no failures are reported by this or any other emission related diagnostic. |
| • | Clear the MIL and the DTC with a scan tool. |
Test Description
The numbers below refer to the step numbers on the diagnostic table.
-
Before you perform this test, the engine must be at the normal operating temperature.
-
The Freeze Frame/Failure Records may help to locate an intermittent condition. If you cannot duplicate the DTC, the information in the Freeze Frame/Failure Records can help to determine how many miles have occurred since the DTC set. The Fail Counter and the Pass Counter can also determine how many ignition cycles have occurred since the diagnostic reported a pass and/or a fail. In order to isolate when the DTC failed, operate the vehicle within the same Freeze Frame conditions that the PCM recorded. These conditions include the RPM, the vehicle load, the vehicle speed, and the temperature.
-
If the scan tool indicates the HO2S voltage goes below 200 mV, the HO2S circuits and PCM are OK.
-
This step verifies whether the HO2S low signal circuit from the PCM is OK.
-
This step verifies whether the HO2S low signal circuit from the PCM is OK. A voltage indicates that the PCM and wiring are OK.
-
Disconnecting the PCM allows using a DMM in order to test the circuit continuity. This procedure helps to locate a circuit that is open or shorted.
Step | Action | Values | Yes | No |
|---|---|---|---|---|
Schematic Reference: Engine Controls Schematics | ||||
1 | Did you perform the Diagnostic System Check-Engine Controls? | -- | ||
|
Important: Before you proceed with this DTC, inspect the HO2S for being secure. A loose sensor can cause this DTC to set.
Does the scan tool indicate that the HO2S voltage is outside the specified range? | 410-490 mV | Go to Step 3 | Go to Step 4 | |
Does the DTC fail this ignition? | -- | Go to Step 4 | Go to Intermittent Conditions | |
Is the HO2S voltage below the specified value? | 200 mV | Go to Step 8 | Go to Step 5 | |
Does the DMM indicate near the specified value? | 5 V | Go to Step 6 | Go to Step 7 | |
Did you find and correct the condition? | -- | Go to Step 12 | Go to Step 10 | |
Did you find and correct the condition? | -- | Go to Step 12 | Go to Step 10 | |
8 |
Did you find and correct the condition? | -- | Go to Step 12 | Go to Step 9 |
9 | Replace the affected HO2S. Refer to Heated Oxygen Sensor Replacement - Bank 1 Sensor 2 and/or Heated Oxygen Sensor Replacement - Bank 2 Sensor 2 . Did you complete the replacement? | -- | Go to Step 12 | -- |
10 |
Did you find and correct the condition? | -- | Go to Step 12 | Go to Step 11 |
11 | Replace the PCM. Refer to Powertrain Control Module Replacement . Did you complete the replacement? | -- | Go to Step 12 | -- |
12 |
Does the DTC run and pass? | -- | Go to Step 13 | Go to Step 2 |
13 | With a scan tool, observe the stored information, Capture Info. Does the scan tool display any DTCs that you have not diagnosed? | -- | System OK | |
