GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Pontiac 🢒 2006 🢒 GTO 🢒 Vehicle Control Systems 🢒 Vehicle DTC Information 🢒 Valve Body and Pressure Switch Replacement

Removal Procedure

    Object Number: 669475 Size: SH
  1. Ensure that removal of the valve body is necessary before proceeding.

    2.    Important: The following components can be serviced without removing the valve body from the transmission:

    • The torque converter clutch solenoid (1)
    • The pressure control solenoid (2)
    • The internal wiring harness (3)
    • The 2-3 shift solenoid (4)
    • The 1-2 shift solenoid (5)
    • The transmission fluid pressure manual valve position switch (6)
    • The 3-2 shift solenoid (7)
    • The torque converter clutch pulse width modulation (TCC PWM) solenoid (8)
  2. Remove the fluid level indicator.
  3. Raise the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.
  4. Remove the catalytic converter assembly from the vehicle. Refer to Catalytic Converter Replacement in Engine Exhaust.
  5. Remove the oil pan, gasket, and filter. Refer to Automatic Transmission Fluid and Filter Replacement .

    6. Object Number: 181573 Size: SH
  6. Disconnect the internal wiring harness electrical connectors from the following components:
    7. • The transmission fluid pressure manual valve position switch (1)
    • The 1-2 shift solenoid (2)
    • The 2-3 shift solenoid (3)
    • The pressure control solenoid (4)
    • The TCC PWM solenoid (5)
    • The 3-2 shift solenoid (6)

    Object Number: 670310 Size: SH
  7. Remove the fluid indicator stop bracket bolt (2).
  8. Remove the fluid indicator bracket (1).

    9. Object Number: 670428 Size: SH
  9. Remove the TCC PWM solenoid retainer (2) with a small screwdriver. Rotate the solenoid (1) in the bore, if necessary, until the flat part of the retainer (2) is visible.
  10. Remove the TCC PWM solenoid (1) in order to access the torque converter clutch (TCC) solenoid retaining bolts.

    11. Object Number: 670430 Size: SH
  11. Remove the TCC solenoid retaining bolts.

    12. Object Number: 71463 Size: SH
  12. Remove the TCC solenoid (with O-ring seal) and wiring harness from the control valve body.
  13. Reposition the harness to the side of the transmission case.

    14. Object Number: 29454 Size: SH
  14. Remove the control valve body bolts which retain the transmission fluid pressure switch to the control valve body.
  15. Remove the transmission fluid pressure switch.

    16. Object Number: 8889 Size: SH
  16. Inspect the transmission fluid pressure switch for damage or debris.

    17. Object Number: 71461 Size: SH
  17. Remove the manual detent spring retaining bolt.
  18. Remove the manual detent spring.
  19. Inspect the manual detent spring for cracks or damage.

    20. Important: Keep the control valve body level when lowering it from the vehicle. This will prevent the loss of checkballs located in the control valve body passages.

  20. Remove the remaining control valve body bolts.

    21. Object Number: 678315 Size: SH
  21. Carefully begin to lower the control valve body down from the transmission case while simultaneously disconnecting the manual valve link.

Installation Procedure

    Object Number: 676923 Size: SH
  1. Install the checkballs (1-7) in the valve body.

    2. Object Number: 678315 Size: SH
  2. Install the control valve body to the transmission case while simultaneously connecting the manual valve link to the manual valve.

    3. Object Number: 670822 Size: SH
  3. Verify that the manual valve link (3) is installed properly to the inside detent lever (1) and the manual valve (2).

    4. Object Number: 670828 Size: SH
  4. Install one bolt (M6 X 1.0 X 47.5) hand tight in the center (1) of the valve body to hold it in place.

    5. Object Number: 13370 Size: SH

    Important: When installing bolts throughout this procedure, be sure to use the correct bolt size and length in the correct location as specified.

  5. Do not install the transmission fluid indicator stop bracket and bolt at this time.

    6. Install but do not tighten the control valve body bolts which retain only the valve body directly.

    Each numbered bolt location corresponds to a specific bolt size and length, as indicated by the following:

    • M6 X 1.0 X 65.0 (1)
    • M6 X 1.0 X 54.4 (2)
    • M6 X 1.0 X 47.5 (3)
    • M6 X 1.0 X 35.0 (4)
    • M8 X 1.0 X 20.0 (5)
    • M6 X 1.0 X 12.0 (6)
    • M6 X 1.0 X 18.0 (7)

    Object Number: 71461 Size: SH
  6. Install the manual detent spring.
  7. Install but do not tighten the manual detent spring retaining bolt.

    8. Object Number: 29454 Size: SH
  8. Install the transmission fluid pressure switch.
  9. Install but do not tighten the control valve body bolts which retain the transmission fluid pressure switch to the control valve body.

    10. Notice: Refer to Fastener Notice in the Preface section.

    Notice: Torque valve body bolts in a spiral pattern starting from the center. If the bolts are torqued at random, valve bores may be distorted and inhibit valve operation.


    Object Number: 7748 Size: SH
  10. Tighten the control valve body bolts in a spiral pattern starting from the center, as indicated by the arrows.

    11. Tighten
    Tighten the control valve body bolts (in sequence) to 12 N·m (106 lb in).


    Object Number: 71461 Size: SH
  11. Ensure that the manual detent spring is aligned properly with the detent lever.

    12. Tighten
    Tighten the manual detent spring bolt to 31 N·m (23 lb ft).


    Object Number: 71463 Size: SH
  12. Install the TCC solenoid with a new O-ring seal to the valve body.

    13. Object Number: 670430 Size: SH
  13. Install the TCC solenoid bolts.

    14. Tighten
    Tighten the TCC solenoid retaining bolts to 12 N·m (106 lb in).


    Object Number: 687049 Size: SH
  14. Install the internal wiring harness to the valve body. The internal wiring harness has a tab (1) on the edge of the conduit.

    15. Object Number: 687206 Size: SH
  15. Place the tab between the valve body and the pressure switch in the location shown (2). Press the harness into position on the valve body bolt bosses (1, 3).

    16. Object Number: 670428 Size: SH
  16. Install the TCC PWM solenoid (1) to the control valve body.
  17. Install the TCC PWM solenoid retainer (2).

    18. Object Number: 670310 Size: SH
  18. Install the transmission fluid indicator stop bracket (1) and bolt (2).

    19. Tighten
    Tighten the transmission fluid indicator stop bracket bolt to 12 N·m (106 lb in).


    Object Number: 181573 Size: SH
  19. Connect the internal wiring harness electrical connectors to the following components:
    20. • The transmission fluid pressure manual valve position switch (1)
    • The 1-2 shift solenoid (2)
    • The 2-3 shift solenoid (3)
    • The pressure control solenoid (4)
    • The TCC PWM solenoid (5)
    • The 3-2 shift solenoid (6)
  20. Install the transmission oil pan and filter. Refer to Automatic Transmission Fluid and Filter Replacement .
  21. Install the catalytic converter assembly from the vehicle. Refer to Catalytic Converter Replacement in Engine Exhaust.
  22. Lower the vehicle.
  23. Fill the transmission to the proper level with DEXRON® VI transmission fluid. Refer to Transmission Fluid Check .

    24. Important: It is recommended that transmission adaptive pressure (TAP) information be reset.

    Resetting the TAP values using a scan tool will erase all learned values in all cells. As a result, The ECM, PCM or TCM will need to relearn TAP values. Transmission performance may be affected as new TAP values are learned.

  24. Reset the TAP values. Refer to Transmission Adaptive Functions .