Circuit Description
The daytime running lamps (DRL) are controlled by the body control module (BCM). The BCM grounds the DRL relay control circuit in order to energize the DRL relay coil. This action provides a path to ground for the RH and LH headlamps through the DRL relay and the DRL resistor. The DRL resistor reduces the intensity of the low beam headlamps for DRL operation. The BCM monitors the low and high beam circuits to ensure that the DRLs are operating properly. If the BCM senses that the DRLs are not operating properly, DTC B2600 is set.
Conditions for Running the DTCs
| • | The ignition switch is in the ON position. |
| • | The headlamp switch is OFF. |
| • | The park brake is unapplied. |
Conditions for Setting the DTC
One or more of the following conditions are present:
| • | The headlamp high beam signal circuit is open. |
| • | The headlamp low beam signal circuit is open. |
| • | The right headlamp battery positive voltage circuit is open. |
| • | The left headlamp battery positive voltage circuit is open. |
Action Taken When the DTC Sets
| • | The BCM turns off the DRL relay control for the remainder of the ignition cycle. |
| • | The SERVICE indicator lights. |
Conditions for Clearing the DTC
| • | The conditions for setting the DTC are no longer present. |
| • | A history DTC clears after 100 malfunction free ignition cycles. |
| • | The BCM receives the clear code command from the scan tool. |
Diagnostic Aids
| • | Check both the LH and RH headlamps for proper operation. |
| • | Check both the LT HEADLAMP and RT HEADLAMP fuses. |
| • | If the DTC is a history DTC, the problem may be intermittent. Refer to General Electrical Diagnosis in Wiring Systems. |
Step | Action | Yes | No |
|---|---|---|---|
Schematic Reference: Headlights/Daytime Running Lights (DRL) Schematics | |||
1 | Did you perform the Lighting System Diagnostic System Check? | Go to Step 2 | |
2 |
Do the headlamps operate properly? | Go to Step 4 | Go to Step 3 |
3 | Are both the high beam and low beam headlamps on one side inoperative? | Go to Step 15 | Go to Step 16 |
4 |
Are the DRL illuminated? | Go to Step 10 | Go to Step 5 |
5 | Is DTC B2602 set? | Go to DTC B2602 | Go to Step 6 |
6 |
Do the DRL illuminate? | Go to Step 7 | Go to Step 8 |
7 |
Do the DRL illuminate? | Go to Step 12 | Go to Step 17 |
8 |
Do the DRL illuminate? | Go to Step 13 | Go to Step 9 |
9 | Test the DRL control circuit for an open or high resistance between the DRL resistor and the fuse block-underhood. Refer to General Electrical Diagnosis and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 22 | Go to Step 14 |
10 | Test the headlamp high beam signal circuit and the headlamp low beam signal circuit for an open or high resistance between the body control module (BCM) and the underhood junction block. Refer to General Electrical Diagnosis and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 22 | Go to Step 11 |
11 | Inspect for poor connections at the harness connector of the BCM. Refer to General Electrical Diagnosis and Connector Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 22 | Go to Step 21 |
12 | Inspect for poor connections at the harness connector of the DRL resistor. Refer to General Electrical Diagnosis and Connector Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 22 | Go to Step 18 |
13 | Inspect for poor connections at the DRL relay. Refer to General Electrical Diagnosis and Connector Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 22 | Go to Step 19 |
14 | Inspect for poor connections at the harness connector of the fuse block-underhood. Refer to General Electrical Diagnosis and Connector Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 22 | Go to Step 20 |
15 | Repair an open, high resistance, or short to ground in the supply voltage circuit of the inoperative headlamp. Refer to General Electrical Diagnosis and Wiring Repairs in Wiring Systems. Did you complete the repair? | Go to Step 22 | -- |
16 | Repair an open or high resistance in the headlamp high beam signal circuit or the headlamp low beam signal circuit of the inoperative headlamp. Refer to General Electrical Diagnosis and Wiring Repairs in Wiring Systems. Did you complete the repair? | Go to Step 22 | -- |
17 | Repair an open or high resistance in the ground circuit of the DRL resistor. Refer to General Electrical Diagnosis and Wiring Repairs in Wiring Systems. Did you complete the repair? | Go to Step 22 | -- |
18 | Replace the DRL resistor. Did you complete the replacement? | Go to Step 22 | -- |
19 | Replace the DRL relay. Did you complete the replacement? | Go to Step 22 | -- |
20 | Replace the fuse block-underhood. Refer to Underhood Electrical Center or Junction Block Replacement in Wiring Systems. Did you complete the replacement? | Go to Step 22 | -- |
21 |
Important: Perform the set up procedure for the BCM. Replace the BCM. Refer to Body Control Module Replacement in Body Control System. Did you complete the replacement? | Go to Step 22 | -- |
22 |
Does the DTC reset? | Go to Step 2 | System OK |
