Step | Action | Value(s) | Yes | No |
|---|---|---|---|---|
1 | Inspect the STOP/HAZ fuse in the fuse block. Is the STOP/HAZ fuse open? | -- | Go to Step 2 | Go to Step 3 |
2 | Locate and repair the source of the overload in CKT 140 (ORN). Is the repair complete? | -- | System OK | -- |
3 | Connect a test light from cavity C 7 of the STOP/HAZ fuse to ground. Does the test light illuminate? | -- | Go to Step 5 | Go to Step 4 |
4 | Repair the open in CKT 3 (PNK) between the fuse block and the ignition switch. Is the repair complete? | -- | System OK | -- |
5 |
Does the test light illuminate? | -- | Go to Step 7 | Go to Step 6 |
6 | Repair the open in CKT 150 (BLK) between cavity K 2 of the multifunction alarm module connector and G 200. Is the repair complete? | -- | System OK | -- |
7 |
Does the chime sound? | -- | Go to Step 15 | Go to Step 8 |
8 |
Does the test light illuminate? | -- | Go to Step 12 | Go to Step 9 |
9 |
Is the resistance greater than the specified value? | 1.0 ohms | Go to Step 11 | Go to Step 10 |
10 | Replace the multifunction alarm module. Refer to Multifunction Alarm Module Replacement . Is the repair complete? | -- | System OK | -- |
11 | Repair the open in CKT 80 (LT GRN) between the multifunction alarm module connector and the key-in warning switch. Is the repair complete? | -- | System OK | -- |
12 | Connect a fused jumper wire from cavity B 3 to cavity B 4 of the key-in warning switch connector. Refer to Using Fused Jumper Wires in Wiring Systems. Does the chime sound? | -- | Go to Step 13 | Go to Step 14 |
13 | Replace the key-in warning switch. Refer to Ignition and Key Alarm Switch Assembly - Disassemble - Off Vehicle in Steering Wheel and Column - Tilt. Is the repair complete? | -- | System OK | -- |
14 | Repair the open in CKT 159 (TAN) between the key-in warning switch and the instrument panel (IP) harness junction block. Is the repair complete? | -- | System OK | -- |
15 | Place the headlamps switch in the PARK or HEAD position. Does the chime sound? | -- | Go to Step 22 | Go to Step 16 |
16 | Inspect the ILLUM fuse in the fuse block. Is the ILLUM fuse open? | -- | Go to Step 17 | Go to Step 18 |
17 | Inspect and repair the source of the overload in CKT 8 (GRY). Is the repair complete? | -- | System OK | -- |
18 | Connect a test light from cavity E 3 of the ILLUM fuse to ground. Does the test light illuminate? | -- | Go to Step 20 | Go to Step 19 |
19 | Repair the open in CKT 44 (DK GRN) between the fuse block and the headlamps switch. Is the repair complete? | -- | System OK | -- |
20 |
Does the test light illuminate? | -- | Go to Step 10 | Go to Step 21 |
21 | Repair the open in CKT 8 (GRY) between the multifunction alarm module and the fuse block. Is the repair complete? | -- | System OK | -- |
22 |
Does the test light illuminate? | -- | Go to Step 10 | Go to Step 23 |
23 | Repair the open in CKT 150 (BLK) between cavity K 1 of the multifunction alarm module connector and G 200. Is the repair complete? | -- | System OK | -- |
